background image

vii

EPC-C301 User Manual

 

Safety Instructions

1.

Please read these safety instructions carefully.

2.

Please keep this User Manual for later reference.

3.

Please disconnect this equipment from AC outlet before cleaning. Use a damp 

cloth. Don’t use liquid or sprayed detergent for cleaning. Use a moist sheet or 

clothe for cleaning.

4.

For pluggable equipment, the socket-outlet should be near the equipment and 

should be easily accessible.

5.

Protect this equipment from humidity.

6.

Lay this equipment on a reliable surface when installing. A drop or fall could 

cause injury.

7.

The openings on the enclosure are for air convection and protecting the equip

-

ment from overheating. DO NOT COVER THE OPENINGS.

8.

Make sure the voltage of the power source when connecting the equipment to 

the power outlet.

9.

Place the power cord such a way that people cannot step on it. Do not place 

anything over the power cord.

10.

 All cautions and warnings on the equipment should be noted.

11.

If the equipment is not used for long time, disconnect the equipment from mains 

to avoid being damaged by transient over-voltage.

12.

Never pour any liquid into ventilation openings; this could cause fire or electrical 

shock.

13.

Never open the equipment. For safety reasons, only qualified service personnel 

should open the equipment.

14.

If one of the following situations arises, get the equipment checked by service 

personnel:



The power cord or plug is damaged.



Liquid has penetrated into the equipment.



The equipment has been exposed to moisture.



The equipment does not work well, or you cannot get it to work according to 

the user's manual.



The equipment has been dropped and damaged.



The equipment has obvious signs of breakage.

15.

Do not leave this equipment in an environment where the storage temperature 

may go below -40 °C (-40 °F) or above 85 °C (185 °F). This could damage the 

equipment. the equipment should be in a controlled environment.

16.

Caution: Danger of explosion if battery is incorrectly replaced. Replace only with 

the same or equivalent type recommended by the manufacturer, discard used 

batteries according to the manufacturer's instructions.

17.

The sound pressure level at the operator's position according to IEC 704-1:1982 

is no more than 70 dB (A).

18.

RESTRICTED ACCESS AREA: The equipment should only be installed in a 

Restricted Access Area.

19.

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advant

-

ech disclaims all responsibility for the accuracy of any statements contained 

herein.

20.

The product is intended to be supplied by an UL certified power supply or dc 

source suitable for use at Tma 60 degree C min. and output meets SELV or 

ES1, rated 12Vdc,5A/12Vdc,10A/9-36Vdc,4.4-1.1A

21.

The wire of the protective bonding conductor shall be green-and-yellow, 

20AWG/0.5(mm2) min.

Summary of Contents for EPC-C301 Series

















































































Reviews: