Advantech EKI-7758F User Manual Download Page 127

Page: 127 / 149

113

Figure C.36: Port Trunk Status

C.2.5 Port Mirroring

The Port mirroring is a method for monitor traffic in switched networks. Traffic through
ports can be monitored by one specific port. That means traffic goes in or out
monitored (source) ports will be duplicated into mirror (destination) port.

•

Rx Destination Port:

There is only one port can be selected to be destination

(mirror) port for monitoring RX traffic which come from source port. User can connect
mirror port to LAN analyzer or Netxray.

•

Tx Destination Port:

There is only one port can be selected to be destination

(mirror) port for monitoring TX traffic which come from source port. User can connect
mirror port to LAN analyzer or Netxray.

•

Mark the check boxes to monitor source receiving or transmitting packets of each

port. And then, click ‘Clear’ button to clear the marks or click ‘Apply’ button to carry
the setting into effect.

Figure C.37: Port Mirroring

C.2.6 Rate Limiting

Summary of Contents for EKI-7758F






















































































































































Search results

Summary of Contents for EKI-7758F

Reviews:

Related manuals for EKI-7758F

Brands by name

Popular brands

Advantech EKI-7758F, User Manual

Search results

Summary of Contents for EKI-7758F

Reviews:

Related manuals for EKI-7758F

Brands by name

Popular brands