Advantech-DLoG DLT-V83 Series Operating Instructions Manual Download Page 56

Page: 56 / 157

Operating the device

56 / 157

DLT-V83 Operating Instructions V2.00

9.2.

Switching the DLT-V83 on/off

Switch the DLT-V83 on and off as follows, depending on the configuration:



Using the <Power> button. Press and hold the <Power> button for 2 seconds.



By applying the supply voltage.



Through the ignition signal of the vehicle.

Fig. 9.1: <Power> button

Time between switching off and on: 10 seconds

After the DLT-V83 has been shut down and switched off, it takes 10 seconds until the device will react to

a switch-on signal (<Power> button / ignition).

9.3.

Operating the touchscreen

Depending on the device model, the DLT-V83 is equipped with a resistive touchscreen or a projected-

capacitive touchscreen with continuous glass front (abbreviated PCT).

TIP: Protective film for resistive touchscreens

Optional protective film is available for the resistive touchscreens.

Details in section

16.12 Protective film for touchscreen (

optional).

Summary of Contents for DLT-V83 Series






























































































































































Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands

Advantech-DLoG DLT-V83 Series, Operating Instructions Manual

Search results

Summary of Contents for DLT-V83 Series

Reviews:

Related manuals for DLT-V83 Series

Brands by name

Popular brands