Advantage Controls MegaTron Series Technical Manual Installation Maintenance Download Page 18 | Manualshive

Page: 18 / 23

Advantage Controls MegaTron Series Technical Manual Installation Maintenance Download Page 18

8. Configure

Provides access to menus to set-up passwords, relay activation, temp scale, display contrast, flow
switch, inputs, history time stamps, factory set-up and system information.

INPUTS-

This screen shows what digital

inputs are available on the unit such as water
meters, flow and drum level alarms.

CONTRAST-

This screen allows for adjusting

the display contrast.

FLOW SW-

Defines a flow switch to be open

or closed with flow.

FACTORY-

A factory only menu

TEMP SCALE-

Set between Celsius or

Fahrenheit

>CONFIGURE<

PASSWORD

CONTRAST

RELAYS

TEMP SCALE

INPUTS

NETWORK

HISTORY

SYS

INFO

FLOW SW

FACTORY

HISTORY –

Sets the history time stamp

interval.

SYS INFO-

Tells unit software specifics.

8.1 Password

>CONFIGURE PASSWORDS<

ADMIN PASSWORD
USER PASSWORD

USER SET UP

ADMIN PASSWORD –

The administrator

password gives access to all menus except
factory set up.

USER PASSWORD –

The user password

allows the user to access HOME menus that
are made available in

USER SET UP

.

8.2 Relays

>CONFIGURE RELAYS<

RELAY 1
RELAY 2

RELAY 3
RELAY 4

RELAY 5

MORE RELAYS

CONFIGURE RELAYS –

This menu lets

you choose what available function (timer 1,
conductivity, alarms etc…) activates a
particular relay. When you select a relay a
pop-up screen appears with a list of all
available activation functions to arrow
through.

8.3 Network

NETWORK –

This menu is used for setting

up the remote WebAdvantage
communications and is covered in a
separate manual.

>CONFIGURE NETWORK<

IP ADDRESS

HTTP REMOTE

IP MASK

FTP

GATEWAY

RESET

SERVER

HTTP LOCAL

18

«
...
16
17
18
19
20
...
»

Summary of Contents for MegaTron Series
























Reviews:

No comments