manualshive.com logo in svg

Advanjet HM-2600, Maintenance And Repair

Share
Download
Advanjet HM-2600 Maintenance And Repair Download Page 24

 

 

3.7.8 

Tuck the Cables 

Press the main air valve cable 
into the slot in the back of the 
top cover, followed by the 
heater/melter cable. Fasten with 
a cable tie as shown. 

3.7.9 

Trim the Cables 

Trim the cable tie end and press 
the fastener until it is fully seated 
in the top cover slot. Carefully 
tuck the wires and connectors 
into the top cover. 

3.7.10  Connect the Air Valve 

 

Attach the air valve cable 
connector as shown. 

 

Carefully tighten the screw.  

 

NOTICE 

Over-tightening can 

easily break this plastic. 

 

3.7.11  Position Mounting 

Plate 

 

Use the alignment pins to 
position the mounting plate. 

 

Take care that the cables 
are not pinched between the 
mounting plate and 
manifold.  

3.7.12  Attach the Mounting 

Plate 

Locate the three mounting plate 
screws that were set aside. 
Apply Loctite 242 to the tips and 
attach as shown. 
 

3.7.13  Attach the Dovetail 

Plate 

Locate the four dovetail plate 
screws that were set aside. 
Apply Loctite 242 to the tips of 
and attach as shown. 
 

Continue to the next section—Set the Jet Hammer Gap. 

 

Page 24 of 28 

Advanjet HM-2600 Hotmelt Jet Maintenance and Repair 

3A6328A 

Summary of Contents for HM-2600





























Reviews:

No comments

Brands by name

Popular brands

Load more brands