background image

5

Call Box Specifications

Without Mounting Bracket: 

 

With Mounting Bracket:

Height:  5.0625”    

 

Height:  5.25”

Width: 

3.25”  

 

 

Width: 

3.4375”

Depth:  1.375”    

 

Depth:  1.625”

Weight:  5.7 oz.    

 

Weight:  7.1 oz.

Battery:   

3.6V lithium

Humidity:  

Up to 90% non-condensing

Temperature: 

20° F to 140° F

Freq. Range: 

902-928 MHz

Auto Check-In: 

3 minutes

The AW-NCB4100(W) is not water resistant – do not submerge in water.

Call Box Cleaning Recommendations

Never use strong cleaning chemicals to clean the surface area of two-

way radios or call boxes. Some examples would be: acetone, bleach, 

window cleaner, degreasers, hand sanitizers, nail polish remover or like 

products. Referencing the above cleaning procedures; Advanced Wireless 

Communications, Inc. does NOT imply that any of these cleaning procedures 

provided is effective in removing or killing potential contaminants or viruses from 

the radio surface. Rather, these recommendations are intended to provide the 

radio user with acceptable alternatives for a cleaner physical environment.

Preferred Cleaning Method 

– 

Use a warm, damp cloth (water only) to wipe all surface areas of the call box. 

The cloth should be damp only, not dripping water. Never hold the call box 

under a running water faucet or submerge in water. After wiping, if moisture is 

seen on the surface of the call box, wipe with a dry cloth to speed drying.

Acceptable Cleaning in Moderation 

Use a mild dish soap and warm water mix, thoroughly submerge the cloth in the 

soap and water solution. Remove the cloth and wring all water out of the cloth. 

The cloth should be damp only, not dripping. Never hold the call box under a 

running water faucet or submerge in water. Wipe all surface areas of the call 

box. After wiping, if moisture is seen on the surface of the call box, wipe with a 

dry cloth to speed drying.

Aggressive Cleaning Method 

Note:

 

Over time, this method can cause undesirable cosmetic effects to the 

label and adhesive areas. It can also cause discoloration to plastics.

Use an over the counter, 75% Isopropyl alcohol concentration to dampen a 

cloth. Damp only, not dripping alcohol. Wipe all surface areas of the call box. 

Alcohol residue will dry quickly.

NEVER apply the 75% Isopropyl alcohol directly to the surface area of the 

call box. Never submerge call box in alcohol.

Summary of Contents for AW-NCB4100










Reviews: