background image

Operation & Maintenance Manual

Table of Contents:

1.0 

Introduction

1

2.0 

Unpacking your COOL-

SPACE

®

1

3.0 

Set-up of COOL-

SPACE

®

unit

1

3.1 

Connecting the water supply

1

3.2 

Connecting the electrical supply

2

4.0 

Operating procedures

3

4.1 

Filling the unit with water

3

4.2 

Starting the fan

3

4.3 

Starting the pump and adjusting the water flow

4

5.0 

Maintenance and storage

4

5.1 

Removing the cooling media & accessing the inside of the unit

4

5.2 

Daily maintenance

4

5.3 

Periodic maintenance

5

5.4 

Storage

5

6.0 

Troubleshooting/Repair

6

6.1 

Troubleshooting

6 - 9

6.2 

Repair procedures

10

6.3 

Technical support

10

7.0 

Warranty

11

7.1 

Warranty form

11

7.2 

Warranty parts

11

7.3 

Optional accessories and replacement parts

11

Due to continuous product innovations, we reserve the right to change product 

specification without due notice.

New evaporative cooling media 

contains a harmless odor; similar to 

new carpet or paint. The media 

should be flushed with water to 

remove the construction odor. A 

REFRESH™ tablet will help control 

odor and bacteria in the reservoir 

and the cooling media.

Instructions:

Fill the reservoir with water

1.
2.

3.

4.

5.

Place the REFRESH™ tablet in the 

reservoir
Turn on the pump,  leaving the fan 

off, and cycle water for 8 hours or 

overnight
Drain used water and refill the 

water reservoir
Repeat when necessary to remove 

odors

Part# CS-T106

To learn more about COOL-

SPACE 

coolers and accessories visit us 
online at

.com

Summary of Contents for CS5-16-VD-TB

















Reviews: