manualshive.com logo in svg

Advanced Instruments Osmo1, User Manual, Page: 59 / 72

Share
Download
Advanced Instruments Osmo1 User Manual Download Page 59

Chapter 8 

Maintenance & troubleshooting

59

Osmo1

®

 Single-Sample Micro-Osmometer User Guide

8.5  Troubleshooting

If you encounter a system error message on the screen 
during operation, you may be able to fix the problem. 
For example, you might need to close the printer door or 
take some other simple action.

If you are unable to resolve the system error, contact 
Advanced Instrument Hot-Line Technical Service for 
assistance. (See “Contacting Advanced Instruments” on 
page 5.)

General errors

Table 10 lists general errors that the system can detect.

Error

Suggested action

AI consumable box 
not detected

• 

Place a Micro-Sample Test Kit 
(P/N: 133800) on the instrument.

Printer door open

• 

Close the printer door.

Printer out of paper

• 

Replace printer paper.

Table 10: General errors

Errors during calibration

For a list of errors that can occur during calibration, see 
Table 6 on page 32.

Errors during testing

Table 11 lists errors that can occur during a test.

If an error occurs during a test, a message displays on 
the screen and is recorded in the events database. 

Discard the sample, carefully clean the plunger, and then 
try a new sample. If the error occurs again, refer to 
Table 11, below, for a possible remedy.

Error

Possible cause/Suggested action

Out of 
range Low

Out of 
range High

Cause: 

The sample might be outside the range 

of the instrument:

• 

“Out of range Low” indicates the measured 

reading is below -10 mOsm.

• 

“Out of range High” indicates the measured 
reading is above 2200 mOsm.

Action:

• 

Test a control such as Clinitrol.

• 

Check for particulate matter in the sample.

Sample did 
not freeze

Cause: 

The sample might be above the range of 

the instrument.

Action:

• 

Confirm sample is present in the sampler.

• 

Test the solenoid. (See “Solenoid 
maintenance” on page 55.)

• 

Test a control such as Clinitrol to see if the 
issue persists.

• 

Clean the sample probe.

Sample 
pre-freeze

Cause:

 The sample froze prematurely.

Action:

• 

Re-run a new sample using a known control 
such as Clinitrol.

• 

Check for particulate matter in the sample.

• 

Clean the sample probe with a chamber 
cleaner dampened with water.

Test timeout

Cause:

 The instrument was unable to complete 

the test within the allotted time.

Action:

• 

Check for particulate matter in the sample.

• 

Test a control such as Clinitrol to see if the 
issue persists.

• 

If the issue persists, the sample might be 
outside the range of the instrument.

Table 11: Testing errors

Summary of Contents for Osmo1









































































Reviews:

No comments