manualshive.com logo in svg

Advanced Instruments Osmo1, User Manual, Page: 57 / 72

Share
Download
Advanced Instruments Osmo1 User Manual Download Page 57

Chapter 8 

Maintenance & troubleshooting

57

Osmo1

®

 Single-Sample Micro-Osmometer User Guide

4. 

Remove the Fuse Holder; then remove the two fuses.

5. 

Insert two replacement fuses into the Fuse Holder 
(Figure 87).

NOTE: 

Use replacement fuse P/N 70011: 
Fuse, 1.0A 250V SB 5 x 20 mm.

NOTE: 

Double-check the values marked on the new 
fuses before you install them. The instrument 
automatically adjusts for voltages between 
100 VAC and 240 VAC, but appropriately rated 
fuses must be installed.

Figure 87: Fuses in Fuse Holder

6. 

Re-install the Fuse Holder into the back of the 
instrument.

7. 

Close the Fuse Holder Door.

8. 

Reconnect the power cord to the Osmo1 and plug it 
into an outlet.

9. 

Power on the Osmo1.

Sampler plunger wire replacement and verification

To ensure proper instrument operation, you should 
replace the sampler plunger wire every 500 tests (or 
each time you empty a Micro-Sample Test Kit).

NOTE: 

A sampler plunger wire is included with each 
Micro-Sample Test Kit.

Failure to replace the plunger wire may affect instrument 
accuracy and repeatability.

NOTE: 

Refer to Figure 88 when completing the sampler 
plunger wire replacement procedure.

Calibration 

gauge & key

Shaft bushing

Shaft

Finger grip

Body

Calibration 

set-screw 

access

Sampler tip

Key

Wire

Tip

Figure 88: Sampler plunger

Summary of Contents for Osmo1









































































Reviews:

No comments