Advanced Card ACR100I Reference Manual Download Page 19

Page: 19 / 20

ACR100I – Reference Manual

[email protected]

Version 1.00

www.acs.com.hk

Page 19 of 20

Appendix A. Supported Card Types

The following table is a list of the card types returned by

GET_READER_INFORMATION

corresponding with the respective card type code:

Card type code

Card Type

00h

Auto-select T=0 or T=1 communication protocol

01h

I2C memory card (1, 2, 4, 8 and 16 kilobits)

02h

I2C memory card (32, 64, 128, 256, 512 and 1024 kilobits)

03h

Atmel® AT88SC153 secure memory card

04h

Atmel® AT88SC1608 secure memory card

05h

Infineon® SLE4418 and SLE4428

06h

Infineon® SLE4432 and SLE4442

07h

Infineon® SLE4406, SLE4436 and SLE5536

08h

Infineon® SLE4404

09h

Atmel® AT88SC101, AT88SC102 and AT88SC1003

0Ch

MCU-based cards with T=0 communication protocol

0Dh

MCU-based cards with T=1 communication protocol

Summary of Contents for ACR100I





















Search results

Summary of Contents for ACR100I

Reviews:

Related manuals for ACR100I

Brands by name

Popular brands

Advanced Card ACR100I, Reference Manual

Search results

Summary of Contents for ACR100I

Reviews:

Related manuals for ACR100I

Brands by name

Popular brands