March 2014
64200796L1-13E
Copyright © 2014 ADTRAN, Inc.
Page 6
Quick Start Guide
NetVanta Unified Communications Demo Kit
P/N 4202797G1
4. Place the call on hold and demonstrate the line keys for
the particular line in use on all phones.
5. Pick up the call on another phone by pressing the line
key that is on hold.
6. Dial in on one of the analog lines to make all the phones
ring.
7. Answer the call on any available phone and repeat
Steps 4 and 5 again.
8. The analog lines will also transfer to the auto attendant
for
Day Mode
and
Night Mode
, depending on which
mode is set in the system scheduler.
D
EMONSTRATING
K
EY
S
YSTEM
M
ODE
U
SING
T1/PRI/SIP T
RUNKS
Two individual SCAs have been created to emulate key
system functionality when connecting the PSTN to a T1,
PRI, or SIP trunk.
• The SCA extensions 103 and 104 have been added to a
Linear Hunt Ring Group, extension 100.
• This ring group can be customized to provide call
coverage where incoming calls will ring the two
extensions (103 and 104) on individual IP phones.
• The call coverage can be configured to ring the lines for
a specified number of rings, and then go to the operator
or voicemail.
SIP T
RUNKS
An example SIP trunk to a generic service provider is
provided. Typically used options are already configured, as
well as advanced options that can only be configured from
the command line interface (CLI).
The
add diversion
and
replace diversion
commands are
only available in the CLI. These commands work in
conjunction with the
diversion-supported
option. Some
service providers require diversion support to allow calls to
be transferred on behalf of a known direct inward dialing
(DID) or billable trunk number (BTN). In the provided
example, the BTN is 2565551111. When a call is blind
transferred by a user, auto attendant, user's call coverage,
or user's FMFM service, the diversion field includes the
BTN so that the call is allowed to transfer and pass the
automatic number identification (ANI) of the calling party
(caller ID).
O
PTIONAL
F
EATURES
The following features can be demonstrated with additional
equipment or steps not provided previously in this
document:
• If a public address (PA)/powered speaker is connected
to the paging port, dial
*30
to make a page.
• If a door relay is connected to the
Door Relay
connection on the rear of the chassis, dial
*38
to
activate the relay for 5 seconds.
• To call the door phone (not provided with the demo kit),
dial
*37
, and the door phone will automatically answer.
The door phone should be connected to the FXS 0/1
port, which is pre-configured for the door phone.
• To call all phones from the door phone, press the
Call
button on the door phone. This calls the door phone
ring group extension 802.
• To demonstrate the Administrative GUI capabilities,
use a personal computer to launch Internet Explorer
®
or Firefox
®
and enter
http://10.10.10.1/admin
. Enter
the user name
admin
and
password
password
. Log
out by pressing the
Logout
link in the top right corner.
• To demonstrate the User GUI capabilities, use a
personal computer to launch Internet Explorer
®
or
Firefox
®
and enter
http://10.10.10.1
. Enter user name
201
and password
1234
.
D
EFAULT
C
ONFIGURATION
To return the NetVanta 7100 to its default demo kit
configuration, refer to
NetVanta 7100 Demo Kit Guide and
available on the ADTRAN Support Forums. The
Support Forums article includes a file attachment with
configuration files and instructions.
B
EST
P
RACTICES FOR
U
PGRADING
Y
OUR
D
EMO
K
IT
This section is relevant if you plan to use components from
a previous demo kit (4200797L1) to upgrade or assemble a
demo kit by ordering equipment individually. Follow the
instructions below as needed to create or upgrade your
Demo Kit.
•
Factory Default IP Phones on page 7
•
Reusing the Pelican Case on page 7
•
Obtain Demo Kit Zip File and Unpack on page 7
•
Copy File to CompactFlash Card on page 7
•
Install the New Configuration File on page 7
•
