ADTRAN NetVanta 6240 Series, Quick Start

Page: 1 / 4

Quick Start
V
OICE
C
ONNECTION
A single 50-pin female amphenol connector provides the interconnect wiring for the analog circuits (FXS and
FXO). Refer to the
NetVanta 6240/6250 Series Hardware Installation Guide at
https://supportforums.adtran.com for detailed pin-out information.
B
ATTERY
B
ACKUP
C
ONNECTION
An optional battery backup system (P/N 1175044L1) is available for the NetVanta 6240/6250 Series. Refer to
the
NetVanta 6240/6250 Series Hardware Installation Guide and to the documentation shipped with the battery
backup system for more information on this connection.
T
HIRD
-P
ARTY
S
OFTWARE
The software included in this product contains copyrighted software that is licensed under the GNU General
Public License (GPL). You can obtain the complete corresponding source code of such software components
from ADTRAN for a period of three years after our last shipment of this product. If electronic distribution is
desired, you may send your request to
OpenSourceReviewBoard@adtran.com .
If distribution on physical media is desired, you can send a request, together with a money order or check for
$5, to:
ADTRAN, Inc. Attn: OSRB Coordinator
901 Explorer Blvd. Huntsville, AL 35806
Please indicate in your request that this is a GPL Source Request. Please also identify the requested product’s
part number. This offer is valid to anyone in receipt of this information.
C
ONFIGURE
Y
OUR
A
PPLICATION
The applications you will need to configure vary by product and by network. Review the list of defaults for your
unit before deciding what applications to configure. At the end of this document is a list of configuration guides
that relate to common applications that should be configured on startup. These guides are all available online
on
ADTRAN’s Support Community .
G
ETTING
S
TARTED
This NetVanta unit ships with a statically assigned IP address of 10.10.10.1 and the ability to connect to a
Dynamic Host Control Protocol
(DHCP) network and receive an IP address assignment from a DHCP server.
When connecting to a DHCP network, this unit supports Zero-Touch Provisioning, allowing the NetVanta router
to download and apply configuration parameters from a configuration management server.
g
NOTE
DHCP is enabled by default on the NetVanta 6250 Series unit only.
Regardless of the method you use to connect the NetVanta unit to the network, there are two methods available
for configuration:
■ Web-based graphical user interface (GUI)
■ Command line interface (CLI)
The GUI lets you configure the main unit settings and provides online guidance and explanations for each
setting. However, using the AOS CLI may be necessary for more advanced configurations.
A
CCESS THE
G
UI
You may access the GUI from a web browser in one of two ways:
Connect via the Static Address
1. Connect the router to your PC using the port labeled GIG 0/1 on the front of the unit.
2. Set your PC to a fixed IP address of 10.10.10.2 . To change your PC IP address, navigate to Computer
> Control Panel > Network Connections > Local Area Connection > Properties > IP (TCP/IP) and
select Use this IP Address . Enter these parameters:
■ IP Address: 10.10.10.2
■ Subnet Mask: 255.255.255.0
■ Default Gateway: 10.10.10.1
You do not need to enter any DNS server information. After the information is entered, select OK twice,
and close the Network Connections dialog box. If you cannot change the PC’s IP address, you will need
to change the unit’s IP address using the CLI. (See “Access the CLI” on page 2.)
3. Open a web browser and enter the unit’s IP address in your browser address line as follows:
http://10.10.10.1 . The default IP address is 10.10.10.1 , but if you had to change the unit’s IP address
using the CLI, enter that address in the browser line.
4. The initial GUI screen appears.
Connect via the DHCP Client Address
1. Connect the router to an existing network that supports DHCP using the port labeled GIG 0/1 on the
front of the device. The NetVanta unit will automatically request an IP address assignment from the
DHCP server.
2. Check the DHCP server and record the IP address assigned to the NetVanta unit.
3. Open a web browser on any network PC that can route to the IP address recorded in Step 2 and enter
the NetVanta unit’s IP address.
4. The initial GUI screen appears.
g
NOTE
It is best to only use the Configuration Wizard for new installations because some existing settings can be lost
or reset when using this wizard.
61700202G1-13D 1
©2018 ADTRAN, Inc.
All Rights Reserved.
NetVanta
NetVanta 6240/6250 Series
October 2018
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
The following configuration guides provide configuration information for applications typically used within this
product. All documents are available online at https://supportforums.adtran.com .
Configuring T1 Access to a Remote Site Using PPP in AOS
Configuring Port Forwarding in AOS
Configuring DHCP in AOS
Configuring VPN using Aggressive Mode in AOS
Configuring Internet Access (Many to one NAT) with the Firewall Wizard in AOS
Configuring QoS for VoIP in AOS
Configuring QoS in AOS
Configuring a VPN using Main Mode in AOS
Configuring PPP in AOS
Configuring Frame Relay in AOS
Configuring the Switchboard and Dial Plan in AOS
Configuring Enhanced ANI/DNIS Substitution in AOS
Configuring HDLC in AOS
Configuring Voice Traffic over SIP Trunks in AOS
Configuring PRI Signaling for DSX-1 in AOS
Configuring Source and ANI Based Routing in AOS
Using Auto-Config in AOS
C A U T I O N !
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
61700202G1-13D
P/N: 4740202G10
4740202G20
4700252F1
4700254F1
4700256F1