Quick Start Guide, 61700531G1-13A, November 2011
1
N
ET
V
ANTA
1110 R
EDUNDANT
P
OWER
S
UPPLY
P/N 1700531G1
4
Copyright © 2011 ADTRAN, Inc. All Rights Reserved.
G
ETTING
S
TARTED
The NetVanta 1110 RPS (P/N 1700531G1) is housed in a 1U-high rack mountable metal
enclosure and includes a universal AC power supply. The NetVanta 1110 RPS provides a
red12 VDC source for powering the NetVanta 1238 PoE (P/N 1700599G2) switch
processor and hardware and -48 VDC for PoE backup. It ships with two mounting brackets and
screws, four rubber foot pads, power cord, and one-meter long RPS cable.
The NetVanta 1110 RPS can be installed in rackmount or tabletop configurations. The following
sections provide step-by-step instructions for rack mounting and tabletop installation.
R
ACK
M
OUNTING
THE
RPS
The NetVanta 1110 RPS can be installed into a 19-inch equipment rack. The following steps guide
you in mounting the RPS into a rack.
The NetVanta 1110 RPS and the NetVanta 1238 PoE RPS base unit
with which it is associated should be installed in a restricted
access location as described in UL 60950-1.
Under full load, the NetVanta 1110 RPS may be hot to the touch.
The NetVanta 1110 RPS is intended
•
to be installed, maintained, and serviced by qualified service personnel
only.
•
for use with NetVanta 1238 PoE RPS (P/N 1700599G2) units only.
•
If installed in a closed or multi-unit rack assembly, the operating
ambient temperature of the rack environment may be greater than room
ambient temperature. Therefore, consideration should be given to
installing the equipment in an environment compatible with the
maximum ambient temperature specified by the manufacturer.
•
Installation of the equipment in a rack should be such that the amount
of air flow required for safe operation of the equipment is not
compromised.
•
Be careful not to compromise the stability of the equipment mounting
rack when installing this product.
•
Consideration should be given to the connection of the equipment to the
supply circuit and the effect that overloading the circuit might have on
overcurrent protection and supply wiring. Appropriate consideration
of equipment nameplate ratings should be used when addressing this
concern.
•
Reliable grounding of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections other than
direct connections to the branch circuit (e.g., use of power strips).
Figure 3. RPS to NetVanta 1238 PoE Connection
P
OWERING
THE
RPS
AND
THE
N
ET
V
ANTA
1238 P
O
E
1.
Plug the female end of the RPS unit’s power cord (provided with the unit) into the power
receptacle labeled
AC Input
on the rear panel of the unit.
2.
Connect the other end (3-prong plug) of the RPS unit’s power cord to the proper 100 to
130 VAC or 190 to 250 VAC grounded receptacle.
3.
Plug the female end NetVanta 1238 PoE unit‘s power cord (provided with the unit) into the
power receptacle labeled
110-240 VAC, 50-60 Hz, 5 A MAX
on the rear panel of the unit.
4.
Connect the other end (3-prong plug) of the NetVanta 1238 PoE unit’s power cord to the
proper 100 to 130 VAC or 190 to 250 VAC grounded receptacle.
A
DDITIONAL
I
NFORMATION
For additional information about accessing and setting up the NetVanta 1238 PoE, refer to the
NetVanta 1230 Series Fast Ethernet Switch Quick Start Guide
article 2518) supplied with your unit or online at
http://kb.adtran.com
.
For additional details on product features, specifications, installation, and safety, refer to
NetVanta 1230 Series Fast Ethernet Switch Hardware Installation Guide
(ADTRAN’s Knowledge
Base article 2517) online at
•
This unit shall be installed in accordance with Articles 300 and 400 of
NEC NFPA 70.
•
Power to the AC system must be from an appropriately rated and
grounded source.
•
Maximum recommended ambient operating temperature is 50
o
C.
100-240 VAC
50-60 Hz
5A MAX
RPS
AC INPUT
RPS OUTPUT
NetVanta 1238 PoE
RPS Connector
NetVanta 1110 RPS
RPS Connector
Offset
Tab
Offset Tab
Thumb
Screw
Thumb
Screw
TOP
TOP
TOP
TOP
TOP
TOP
TOP
TOP
