ADTRAN 602, Quick Start

Page: 3 / 4

61287800F1-13A 3
3. Attach one end of the cable to the SFP+ WAN or XFP WAN port on
the front of the ADTRAN 602.
Step 5: Connect Power
To connect power to the ADTRAN 602, complete the following steps:
1. Plug the supplied 12V AC/DC Power Converter into the POWER
connection on the front of the ADTRAN 602.
2. Connect the Power Converter to a standard 100-240V AC outlet.
3. Verify the power is on by checking the
POWER
LED on the
ADTRAN 602. The LED should be green indicating local power is
on.
Step 6: Connect UPS (Optional)
The UPS must be UL Listed, and have a
LPS
with an output rated at 12
VDC minimum 3.0 Amps and suitable for the intended location.
The UPS connection on the front of the ADTRAN 602 is used to connect a
commercial UPS Battery backup unit. To connect the USP backup power
supply, complete the following steps:
1. Connect the power cord from the UPS Battery backup unit to the
UPS connection on the front of ADTRAN 602.
2. Connect the UPS Battery backup unit to a regular 100-240 VAC
outlet.
F
RONT
P
ANEL
LED
S
When the ADTRAN 602 first powers up it performs self-tests. Once the
power up self-tests are complete, the status
LEDs
will reflect the true
state of the hardware.
Resetting the ONT
w
NOTICE
Resetting the ONT returns all settings to their factory defaults. Regis-
tration provisioning will be lost.
A reset button is available if the ADTRAN 602 needs to be rebooted. To
reset the ADTRAN 602, press the RESET button for 5 seconds or longer.
A
CRONYMS
AWG American Wire Gauge
GE Gigabit Ethernet
LAN Local Area Network
LED Light Emitting Diode
LPS Local Power Supply
Label Status Indication
POWER


Off
ON Power is off
Power is on
WAN 

2


Off
Yellow
Yellow Flashing
Green
Red No light detected from OLT
ONT detects light from OLT
Ranging in process
ONT is ranged and up
ONT discovered, but not active
LAN


2

2

Off
Green
Green Flashing
Yellow
Yellow Flashing
Red LAN is down
10G link is up
Data transfer in process
Data rate is out of range
Data transfer in process
Port is Administratively up, Link is
down
NG-PON Next Generation Passive Optical Network
ODC Optical Directional Coupler
OMCI OpenManage TM Client Instrumentation
ONT Optical Network Terminal
PON Passive Optical Network
SC/UPC Standard Connector/Ultra Physical Contact
SFP Small Form-factor Pluggable
UPS Uninterruptible Power Supply
TWDM Time and Wavelength Division Multiplexing
WAN Wide Area Network
XFP 10G Form-factor Pluggable
XGSPON Ten Gigabits Passive Optical Network
Operational Specifications
■
Electrical
♦
Operating Voltage: 12 VDC
♦
AC to DC Power Supply: 100 to 240 VAC, 50 to 60 Hz
♦
Power Consumption: Typical 25 watts
■
Physical
♦
8.0 inches wide (20.0 centimeters)
♦
8.0 inches deep (20.0 centimeters)
♦
1.75 inches high (4.5 centimeters)
♦
Weight: 2 pounds (0.9 kilograms)
■
Environmental
♦
Operational Temperature: –5°C to +50°C (+23°F to 122°F)
♦
Storage Temperature: –2°C to +85°C (+28°F to 185°F)
♦
Relative Humidity: 90%, noncondensing
M
AINTENANCE
The ADTRAN 602 does not require routine hardware maintenance for
normal operation. ADTRAN does not recommend that repairs be
attempted in the field. Repair services may be obtained by returning the
defective unit to ADTRAN. Refer to the warranty for further information.
Field support for software is provided through upgrade facilities.
S
AFETY AND
R
EGULATORY
f
WARNING!
■ Read all warnings and cautions before installing or servicing this
equipment.
■ Refer to the national, state and local electrical codes for the
requirements for power and grounding wiring methods.
■ The Gigabit Ethernet port(s) are classified as Type 4a, as defined in
Appendix B of GR-1089-CORE, and is/are suitable for connection to
intra-building, unexposed, wiring or cabling only. Do not metallically
connect the Gigabit Ethernet port(s) to interfaces which connect to
exposed or Outside Plant (OSP) wiring or cabling. The Gigabit
Ethernet port(s) is/are designed for use as intra-building interface(s)
only (4a ports as described in GR-1089-CORE) and requires isolation
from exposed OSP cabling. The addition of Primary Protectors is not
sufficient protection in order to connect the interface metallically to
OSP wiring.
C
CAUTION!
■
This product contains or uses a Class 1 Laser module that complies
with FDA 21 CFR 1040.10, 1040.11 and IEC 60825-1. For continued
compliance with the above standards, only approved Class 1 laser
modules from an ADTRAN approved vendor list (located on the