ADTRAN 47006362F1, Quick Start

Page: 3 / 4

617006364F1-13E 3 2 617006364F1-13E
M
ANUALLY
C
ONFIGURING THE
U
NIT
’
S
IP A
DDRESS
g
NOTE
The configuration parameters used in the examples outlined in this document are for
instructional purposes only. Please replace all underlined entries (
example ) with your
specific parameters to configure your application.This step is unnecessary if the unit’s IP
address has been configured automatically using DHCP.
The NetVanta 6360 unit’s IP address can be configured from either the Gigabit Ethernet
subinterface (for a user network interface (UNI)) or the system management Ethernet virtual
connection (EVC) (for a network-to-network interface (NNI)).The following steps assign an
IP address and subnet mask for the
GIG 0/2.1 Gigabit Ethernet subinterface.
1. At the # prompt, enter config terminal .
2. At the (config)# prompt, enter interface gig 0/2.1 to access the configuration
parameters for the Gigabit Ethernet subinterface.
3. Enter ip address 192.168.1.1 255.255.255.0 to assign an IP address to the Ethernet
subinterface using a 24-bit subnet mask.
4. Enter exit to exit the Gigabit Ethernet subinterface commands and return to the
Global Configuration mode.
5. Enter ip route 0.0.0.0 0.0.0.0 192.168.1.254 to add a default route to the route table.
0.0.0.0 is the default route and the default subnet mask, and 192.168.1.254 is the
next-hop IP address to which the AOS unit should send all of its traffic. You will need
to enter the proper route, subnet mask, and gateway for your network. This
information is typically provided by an Internet service provider (ISP) or local network
administrator.
6. Enter do write memory to save the current configuration.
N
ET
V
ANTA
6360 D
EFAULTS
Feature Default Value
User Name admin
Password password
Enable Password password
HTTP Server Disabled
Event History Enabled
IP Routing Enabled
DHCP Client Enabled
Auto-Config Zero Touch Provisioning Enabled
3. Provide power to the unit as appropriate. Refer to the
NetVanta 6360 Hardware
Installation Guide available online at https://supportforums.adtran.com for more
details.
4. Once the unit is powered up, open a VT100 terminal session using the following
settings: 9600 baud, 8 data bits, no parity bits, 1 stop bit, and no flow control. Press
ENTER to activate the AOS CLI.
5. Enter enable at the > prompt and enter the Enable mode password when prompted.
The default password is password .
You can also access the CLI from a Telnet or SSH client. In order to do this, you must know
the IP address of the AOS device. If you do not know the unit’s IP address, you must use
the
CONSOLE port to access the CLI. To access the CLI using a Telnet or SSH client,
follow these steps:
1. Connect the NetVanta unit to your PC using an Ethernet cable connected to the
GIG 0/2 Gigabit Ethernet port on the front of the device or connect the NetVanta unit
to an existing network that supports DHCP using the GIG 0/2 Gigabit Ethernet port on
the front of the device.
2. Open a Telnet or SSH client on your computer and enter 10.10.10.1 . If your unit
received an IP address from a DHCP server or you have changed your unit’s IP
address, you will need to enter that address.
3. For SSH, log into the unit using the default login ( admin ) and password ( password ).
For Telnet, only the default password ( password ) is required.
4. Enter enable at the > prompt and enter the enable password when prompted. The
default password is password .
C
HANGE
L
OGIN
P
ASSWORDS
1. To modify the user accounts and passwords, from the (config)# prompt, enter the
command username <username> password <password> .
2. To modify the Enable mode password, from the (config)# prompt, enter the
command enable password <password> .
3. To modify the Telnet password, from the (config)# prompt, enter the command line
telnet 0 4 and then press ENTER. Enter the command password <password> .
4. Enter do write to save the current configuration.
C
OMMON
CLI C
OMMANDS
The following are common CLI commands and tips for getting started with the CLI.
■ Entering a question mark (?) shows contextual help and options. For example, entering
? at the prompt will show all commands available from that prompt.
■ To view interface statistics, enter show interfaces <interface type> <interface number> .
■ To view the current configuration, enter show running-config .
■ To view all the IP Addresses currently configured, enter show ip interfaces brief .
■ To view the AOS version, serial number, and other information, enter show version .
■ To view the routing table, enter show ip route .
■ To save the current configuration, enter write .