2
61442880F1-22A
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
This product is designed to meet the following environmental
classes:
ETSI EN 300 019-1-1 “Classification of environmental
conditions; Storage Class” 1.2
ETSI EN 300 019-1-2 “Classification of environmental
conditions, Transportation”, Class 2.3
ETSI EN 300 019-1-3 “Classification of environmental
conditions, Stationary use at weather protected locations”,
Class 3.3
This product is designed to function without degradation during
exposure to all test severities per Class 3.3 of ETSI EN 300 019-1-3.
This product meets EU RoHS Directive 2002/95/EC and/or
applicable exemptions. Refer to
www.adtran.com
for further
information on RoHS/WEEE.
FRANÇAIS
AVERTISSEMENT
!
Lisez tous les avertissements et mises en garde avant l’installation
de cet équipement ou la réalisation de toute opération de
maintenance.
ATTENTION
C
Ce produit utilise un module laser de classe 1 qui conforme aux
normes 21 CFR 1040.10, 1040.11 et IEC 60825-1 et -2. Pour assurer
la conformité aux normes mentionnées plus haut, seuls des
modules laser de classe 1 approuvés provenant d’une liste de
fournisseurs certifiés par ADTRAN (disponible sur le site
d’ADTRAN) doivent être installés sur ce produit. ADTRAN ne
peut certifier l’intégrité d’un système doté d’autres modules laser.
ATTENTION
!
L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des
modules,portez un bracelet de décharge antistatique pour
éviter d'endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d'un
branchement de mise à la terre.
Selon le document GR-1089-CORE, ce système est conçu et
prévu pour une installation intégrée à un réseau demasse
maillé. Ce système n'est pas conçu ni prévu pour une
installation intégrée à un réseau de masse isolé (IBN).
Selon le document GR-1089-CORE section 9, ce produit n'est
pas équipé d'une connexion DC interne entre le retour de la
batterie et la masse du châssis. Ce produit peut être installé
dans une configuration DC-I (isolé) ou DC-C (commun). Pour
les installations où les autres cartes ou le système hôte
possèdent des connexions internes entre le retour de
S
AFETY
AND
R
EGULATORY
C
OMPLIANCE
E
NGLISH
WARNING
!
Read all warnings and cautions before installing or servicing this
equipment.
CAUTION
C
This product uses a Class 1 Laser module that complies with 21
CFR 1040.10 and 1040.11 and IEC 60825-1 and -2. For continued
compliance with the above standards, install only ADTRAN-
approved Class 1 Laser Modules in this product. For a list of
A D T R A N - a p p r o v e d S F P s a n d X F P s , s e e
adtran.com>support>support community>search
SFP/XFP.
ADTRAN cannot certify system integrity with other laser
modules
CAUTION
!
Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
Per GR-1089-CORE this product is designed and intended for
installation as part of a Common Bonding Network (CBN).
This product is not designed nor intended for installation as
part of an Isolated Bonding Network (IBN).
Per GR-1089-CORE Section 9, this product does not have an
internal DC connection between -48 VR and frame ground.
This product can be installed in a DC-I (isolated) or DC-C
(common) installation. For installations where other cards or
the host system have internal connections between -48 VR and
frame ground, the system would be intended for deployment
only in a DC-C installation.
The chassis frame ground terminal must be connected to an
earth ground to ensure that the metal enclosure of the SFP/
XFP is properly grounded via the backplane connector.
NOTE
The Gigabit Ethernet port(s) are optical and therefore are not
classified as any type of port as defined in Appendix B of GR-
1089-CORE.
■
This product is designed to be deployed in GR-3108-CORE
environmental Class 1 and 2.
This product meets or exceeds all the applicable requirements of
NEBS, Telcordia GR-63-CORE, GR-1089-CORE, and ETSI EN
300368. This product is intended for deployment in Central Office
type facilities, EEEs, EECs, and locations where the NEC applies
(for example, Customer Premises).
This product is to be installed in ADTRAN products in Restricted
Access Locations only, and installed by trained service personnel.
