background image

MODULE DIAGNOSTICS

 - 1 OF 2

MODULE ST

A

TUS DURING: 

LED 2*

LED 1**

LED STATUS

DIAGNOSTIC

MODULE PROGRAMMING

Flashing RED

Missing/wrong information from firmware or vehicle. 
See firmware specific diagnostics, or contact technical support.

Solid RED

Module waiting for more vehicle information. Programming incomplete.

Flashing GREEN

Additional steps required to complete programming. Refer to install guide.

Solid GREEN then OFF

Module programming completed successfully. 

o

OFF

No activity or module already programmed.

1 RED flash

No firmware on module. Connect to Weblink and flash device.

2 ORANGE flashes

Contact technical support.

3 ORANGE flashes

Module programming not completed.

4 ORANGE flashes

Contact technical support.

7 ORANGE flashes

Contact technical support.

8 ORANGE flashes

Loop not cut. Ensure loop is cut for automatic transmission. Reset and re-learn.

9 ORANGE flashes

Loop not cut. Ensure loop is cut for automatic transmission. Reset and re-learn.

10 ORANGE flashes

Boot loader update failed. Contact technical support.

11 ORANGE flashes

T-harness detection does not match install type selection in Weblink.

T

A

CH PROGRAMMING

Solid RED

Tach learn in progress.

1 GREEN flash

Tach signal programmed in analog.

2 GREEN flashes

Tach signal programmed in data.

3 RED flashes

No tach signal detected

4 RED flashes

System is in valet mode. Turn off valet mode to program tach.

6 RED flashes

Engine sensing set for ‘assumed start’. No tach programming required.

7 ORANGE flashes

Engine sensing not configured properly. Contact technical support.

* LED 2 (RS) displays generic diagnostic codes specific to the remote start module. Orange LED flashes may appear red. 
** LED 1 (Bypass) displays diagnostic codes specific to the firmware loaded on the module. 
Visit the programming diagnostics page for more information.

PAGE 12 OF 13

U.S. Patent No. 8,856,780 CA 2759622 
Automotive Data Solutions Inc. © 2021 

www.idatalink.com

RSA-AUD2-[CMVWXA0]-EN

2016 Audi S4 PTS with keyport   Automatic

Doc No.: A558F12 - 20211223_151400

Summary of Contents for idatastart CMVWXA0














Reviews: