background image

4 DRIVE FUNCTIONS, DESCRIPTION OF OPERATION

OPENING AND cLOSING ThE DOOR
Press the control button for ~0.5 sec. the door will start moving after you re-
lease the button. 

AUTOMATIc ROLL-BAck
if the door pushes against an obstacle while it is closing, it will stop automati-
cally and roll back.

STOPPING ThE DOOR 
Press the control button one time to stop the door while it is moving.

ADjUSTMENT Of ThE wIDTh Of DOOR OPENING
open the door. move it to the required position by hand. Press the control but-
ton for ~10 sec. until you hear 2-times sound signal. release the button. now 
the drive will automatically remember the adjusted width of the opening.

SLIDING DOOR fIxING
the drive can operate in 2 modes: 
with fixing (factory settings) picture 4).
without fixing (picture 3).
to change the mode to operating without fixing press the control button for 
~15 sec. until you hear 3 long sound signals. release the button.

 

NOTE

 

Operating mode without fixing is used if there is a lock drive. Emer-

gency opening of the door from the outside is possible in this operat-

ing mode. 

RETURN TO fAcTORy SETTINGS
Press the control button for ~20 sec. until you hear 4-times sound signal. re-
lease the control button. all drive settings will return to factory settings.

 

NOTE

 

The  drive  settings  will  automatically  return  to  factory  settings  in 

case of power outage.

Summary of Contents for Croco



















Reviews: