background image

 

Introduction 

 5 

  Memory size is controlled by device driver from 1 MB up to 11 MB 

 

PCI Bus Ethernet Interface: 

  Primary port : Built-in i815E chip + 

82562EM (All of NuPRO-780 

series)

 

  Secondary port : Intel 82559 (For NuPRO-780DV only) 

  PCI local bus Ethernet controller 

  10/100Mbps operation in a single port PCI bus master architecture 

  IEEE 802.3 10base-T and 100base-TX compatible physical longer 

support 

 IEEE802.3u 

auto-negotiation 

support for automatic speed selection 

  IEEE 802.3X (100base-TX Flow control support) 

  Wake on LAN support 

  External LAN status LED connectors 

 

Enhanced IDE: 

Bus Master IDE controller, two EIDE interfaces for up 

to four devices, support PIO Mode 3/4 or Ultra DMA/100 IDE devices, 
including Hard Disk Drive, ATAPI CD-ROM, LS120, and ZIP drives. 

 

Super I/O Chipset: Winbond W83627HF 

 

Parallel Port:  

  One high-speed parallel port, SPP/EPP/ECP mode 

  ESD protection to 4KV 

  Downstream device protection to 30V 

 

Serial Port: 

  One 16550 UART compatible ports with RS-232 interface 

  One 16550 UART compatible ports with RS-232/422/485 (With 

RS-485+ Auto-Direction Technology) 

  ESD protection to 2KV 

 

FDD Interface: 

Two floppy drives (360KB, 720KB, 1.2MB, 1.44MB, 

2.88MB) 

 

USB Interface: 

Two USB pin-header connectors, compliant with USB 

Specification Rev. 1.1, Individual over-current protection

 

 

AC’97 Link: 

Summary of Contents for NuPRO-780 Series












































Reviews: