ADLINK Technology DMI-1210 User Manual Download

Page: 89 / 103

DMI-1210

6.5.4

South Cluster Configuration

6.5.5

HD-Audio Configuration

LPSS Configuration

Selects I2C support mode

BIOS Item

Options

Description

HD-Audio

Configuration

Submenu

LPSS Configuration

Submenu

PCI Express

Configuration

Submenu

SATA Drives

Submenu

SCC Configuration

Submenu

USB Configuration

Submenu

Miscellaneous

Configuration

Submenu

BIOS Item

Options

Description

HD-Audio Support

Disabled

Enabled

Enables/disables HDA Audio

Audio Output

Selection

Enabled

Disabled

Selects audio output, from speaker

out or line out.

BIOS Item

Options

Description

LPSS I2C #X

Support

PCI Mode

ACPI Mode
Disabled

Set LPSS I2C Device Mode.

Set LPSS I2C #X

Speed

Fast Mode

Set LPSS I2C #X Speed Mode.

Summary of Contents for DMI-1210








































































































Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands

ADLINK Technology DMI-1210, User Manual

Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands