ADLINK Technology DMI-1210 User Manual Download

Page: 75 / 103

DMI-1210

6.4.1

CPU Configuration

BIOS Item

Options

Description

EIST

Disable

Enable

Enables/disables Intel SpeedStep

Turbo Mode

Disable

Enable

Enables/disables Turbo mode

Intel Virtualization

Technology

Disable

Enable

When enabled, VMM can utilize the

additional hardware capabilities
provided by Vanderpool Technology

C-States

Disable

Enable

Enables/disables C-States

Enhanced- C-status Disable

Enable

Enables/disables C1E, where, when

enabled, CPU will switch to minimum

speed when all cores enter CStates.

Max Package C

Status

PC2

PC1
C0

Sets the Max Package C State

supported by the processor, from

among PC2, PC1, and C0.

Max Core C State

Core C6

Core C1
Unlimited

Sets the Max Core C State

supported by the cores, from among

Fused value, Core C6, Core C1,

Unlimited

C-State Auto

Demotion

Disable

Configures C-State Auto Demotion.

C-State Un-

demotion

Disable

Configures C-State Auto Un-

demotion.

DTS

Disable

Enable

Enables/disables Digital Thermal

Sensor.

Summary of Contents for DMI-1210








































































































Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands

ADLINK Technology DMI-1210, User Manual

Search results

Summary of Contents for DMI-1210

Reviews:

Related manuals for DMI-1210

Brands by name

Popular brands