manualshive.com logo in svg

ADLINK Technology cPCIS-1100 Series, User Manual, Page: 15 / 48

Share
Download
ADLINK Technology cPCIS-1100 Series User Manual Download Page 15

Backplane 

x

 11 

3

 

Backplane

In this chapter, we will describe the backplanes for the cPCIS-1100 Series 
subsystems. The following table specifies the backplane(s) that correspond 
to each model. 

 backplane 

slots 

power 

backplane 

cPCIS-1100A[R] cBP-3208[R]  8 

— 

cPCIS-1101[R] cBP-3208[R]  8 

cBP-3061 

cPCIS-1102[R] cBP-3208[R]  8  cBP-3062A 

cPCIS-1202[R] 

(dual system) 

cBP-3206[R] 

(x2) 

6 

 (x2) 

cBP-3061 

(x2) 

cPCIS-ET1101 cBP-3208  8  cBP-3061 

cPCIS-ET1102 cBP-3208  8  cBP-3062A 

 

3.1 cBP-3208[R] 

Backplane 

The cBP-3208[R] is a 3U CompactPCI 32-bit backplane with optional rear I/O 
(designated by an “R” suffix). It is used by the cPCIS-1100A / cPCIS-1101 / 
cPCIS-1102 / cPCIS-ET1101 / cPCIS-ET1102. 

Specifications 

Standard CompactPCI height for 3U cPCI cards 
CompactPCI Compliancy 

PICMG 2.0 CompactPCI core specification R3.0  
PICMG 2.1 CompactPCI hot swap R2.0  

Dimensions: 141.3 x 128.7 mm 
PCI bus clock: up to 32-bit/33MHz 
System Slot: one R-hand side dual-slot  
System Slot Rear I/O: P2 rear I/O with AB-type shroud 

Summary of Contents for cPCIS-1100 Series

















































Reviews:

No comments