WiFly QA5 IP ADJ RFC Operation
The ADJ
RFC
remote
(sold seperately) has many different functions and
allows you to control your WiFly QA5 IP from long distance. The ADJ
RFC
remote can control your system up to 150 ft. To use the RFC you
must first activate the fixtures receiver, to activate the receiver please
see the instructions on page 14.
BLACKOUT
-
Pressing this button will blackout the fixture.
AUTO RUN
-
This button will run an automatic program. There are 3
Auto Run programs to choose from. Each press of the button will switch
between the different modes. You can control the speed of the Auto Run
modes by pressing the SPEED button and then pressing the “+” and “-”
buttons.
• AFXX = Color Fade mode, there are 16 Color Fade modes to choose
from. Use the UP or DOWN buttons to scroll through the different
Auto Fade modes.
• AJXX = Color Change mode, there are 16 Color Change modes to
choose from. Use the UP or DOWN buttons to scroll through the
different Auto Change modes.
• A-JF = Both Color Fade and Color Change modes running.
PROGRAM SELECTION
-
Press this button to switch between Static
Color mode and Slave mode. Each press of this button will switch be-
tween the two modes. When in Static Color mode, use the “+” or “-” to
scroll through the 64 colors. Once you have found your color, you can
press the FLASH button to activate strobing and use the “+” or “-” to ad-
just the Flash rate.
FLASH
-
This button will activate the flash (strobe) effect. You can con-
trol the flash speed by pressing the “+” and “-” buttons.
SPEED
-
Press this button and use the “+” & “-” buttons to adjust the
speed of the Auto run mode.
R G B W/A -
Press either one of these buttons and the press the “+” or
“-” to adjust the brightness. Press the FLASH button to activate strobing
and use the “+” or “-” to adjust the Flash rate.
“+” and “-” -
Use these buttons to adjust the flash rate, speed of the
Auto Run mode, Auto Run program selection, sound sensitivity, and
color select.
ADJ Products, LLC - www.adj.com - WiFly QA5 IP User Manual Page 14
ADJ Products, LLC - www.adj.com - WiFly QA5 IP User Manual Page 13
WiFly QA5 IP WiFly Set Up
WiFly QA5 IP WiFly Master-Slave Set Up
With this feature you are able to control the unit with DMX without the need
of XLR cables. Your DMX controller must be connected to a ADJ WiFly
TransCeiver to use this function. You are able to communicate up to 400 feet
(open line of sight)
NOTE: The ADJ RFC control must be set to OFF to use this function.
See pages 10-11 to turn OFF ADJ RFC.
1. Turn on the WiFly function using the instructions on page 11.
2. Follow the instructions on page 11 to set the Wireless address. The
address must match the address set on the WiFly Transceiver.
3. After you have set the WiFly address, follow the DMX instructions on
pages 9-10 to select your desired DMX Channel mode and set your
DMX address.
4. Apply power to the ADJ WiFly Transceiver. The fixture must be set up
first before you apply power to WiFly Transceiver.
Note: If the sync does not work, switch the WiFly power off then on again.
This feature will let you link units to run in a master-slave mode without the
use of XLR cables.
NOTE: The ADJ RFC control must be set to OFF on all the units to use
this function. See pages 10-11 to turn OFF ADJ RFC.
1. Follow the instructions on page 11 to set the Wireless address. The
addresses on each fixture must be the same.
2. After you have set the WiFly address, select your master unit and set
your desired operating mode.
3. Turn on the WiFly function using the instructions on page 11.
4. For the Slave units, put the unit in Slave mode. See page 15 Master-
Slave configuration when setting the unit as a Slave. Then switch ON the
WiFly power switch.
NOTE: If they do not sync up master-slave, switch the Master fixtures
WiFly power switch off then on again.