A.D.J. Supply Europe B.V.
– www.americandj.eu – Stinger II Instruction Manual Page 10
SYSTEM MENU (continued)
CHND -
This will let select your desired DMX channel mode.
1.
Press the MENU button until “
CHND
” is displayed, press ENTER. The current DMX channel mode will be
displayed
2. Press the UP or DOWN buttons to find your desired DMX channel mode and press ENTER to confirm and
exit.
SHND
-
Show modes 0-7 (Factory programs).
1.
Press the MENU button until “
SHND
” is displayed, press ENTER.
2.
“Sh X
” will now be displayed, “
X
” representing a number between 0-7. Shows 1-7 are factory programs,
while show “0” is random mode. Use the UP or DOWN buttons to find your desired show.
3. When you have found your desired show press ENTER, then press and hold the MENU button for at least 3
seconds to activate. After you have set your desired show, it can be changed at any time using the UP or
DOWN buttons.
UVSP
-
UV activation/speed control.
1
. Press the MENU button until “
UVSP
” is displayed, press ENTER.
2. The display will show either “
FAST
” or “
SLOW
”. Use the UP and DOWN buttons to highlight your selection.
3. Press ENTER to confirm.
SLND
-
This will let you set unit as a master or slave in a master/slave configuration.
1. Press the MENU button until “
SLND
” is displayed, press ENTER. Either “
MAST
”, “
SL
1”,
or “
SL 2
” will be
displayed.
2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to confirm.
Note
: In a Master/Slave configuration you can set one fixture to
Master and then set the next fixture to “
SL 2
”,
the fixtures will now have contrast movement to each other.
SOUN
-
Sound Active mode.
1. Press the MENU button until “
SOUN
” is displayed, press ENTER.
2. The display will show either “
ON
” or “
OFF
”. Press the UP or DOWN buttons to select “
ON
” to activate sound
active
mode, or “
OFF
” to deactivate sound active mode.
3. Press ENTER to confirm.
SOSE
- I
n
this mode you can adjust the sound sensitivity.
1. Press the MENU button until “
SOSE
” is displayed, press ENTER.
2. A number between 0-100 will be displayed. Press the UP or DOWN buttons to adjust the sound sensitivity.
0 being the least sensitive, and 100 being the most sensitive.
3. When you have found your desired setting press ENTER to confirm.
DNST
-
This mode can be used as a precaution mode, that in case the DMX signal is lost,
interrupted, or power is lost, the operating mode chosen in the setup is the running mode the
fixture will go into when the DMX signal is lost. You can also set this as the operating mode you
would like the unit to return to when power is applied.
1. Press the MENU button until “
DNST
” is displayed, and either “
MASL
”, “
BLND
”, or “
LAST
” will be displayed
beneath.
2. Press ENTER and the bottom choice will begin to flash. Use the UP or DOWN buttons to choose an
operating mode you would like the unit to start up in when power is applied or the DMX signal is lost.
•
LAST
- If the DMX signal is lost the fixture will stay in the last DMX setting. If power is applied and this mode
is set, the unit will automatically go into the last DMX set up.
•
MASL
(Master Slave) - If the DMX signal is lost or power is applied, the unit will automatically go into Master
Slave mode and run a built-in show.
•
BLND
(Blackout) - If the DMX signal is lost or interrupted, the unit will automatically go into stand by mode.
3. Press ENTER to confirm your desired set up.