PinPoint GO COLOR Safety Precautions
ADJ Products, LLC - www.adj.com - PinPoint GO COLOR User Manual Page 4
ADJ Products, LLC - www.adj.com - PinPoint GO COLOR User Manual Page 5
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture
• Do not spill water or other liquids into or on to your unit.
• Be sure that the local power outlet match that of the required volt-
age for your unit.
• Do not attempt to operate this unit if the power cord has been
frayed or broken. Do not attempt to remove or break off the ground
prong from the electrical cord. This prong is used to reduce the risk
of electrical shock and fire in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user
serviceable parts inside.
• Never operate this unit when it’s cover is removed.
• Never plug this unit in to a dimmer pack
• Always be sure to mount this unit in an area that will allow proper
ventilation. Allow about 6” (15cm) between this device and a wall.
• Do not attempt to operate this unit, if it becomes damaged.
• This unit is intended for indoor use only, use of this product out`
doors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to the point they exit from the unit.
• Cleaning -The fixture should be cleaned only as recommended by
t he manufacturer. See page 3 for cleaning details.
• Heat -The appliance should be situated away from heat sources
such as radiators, heat registers, stoves, or other appliances (inclu-
d ing amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a
marked change in performance.
1. Handling of Batteries
1.1 Do Not Short Circuit the Battery
Try to never short circuit the battery. It generates a very high current
which could cause the battery to overheat which may result in elec-
trolyte gel leakage, harmful fumes, or explosion. The LIR tabs may
easily short-circuit by placing them on conductive surface. A short cir-
cuit may lead to heat build up and damage of the battery. An appro-
priate circuitry with PCM is employed to protect accidental short
circuit of the battery pack.
1.2 Mechanical shock
Droping the unit, impact hit, bending, etc. may cause failure or short-
end life of the LIR battery.
2. Other
2.1 Battery connection
1). Direct soldering of wire leads or devices to the battery is strictly
prohibited.
2). Lead tabs with pre-soldered wiring shall be spot welded to the
batteries. Direct soldering may cause damage of components, such
as separator and insulator, by heat build up.
2.2 Prevention of short circuit within a battery pack
There is enough insulation layers between wiring and the batteries to
provide extra safety protection. The battery pack is constructed in a
way that no short circuit will occur which may cause smoke or fire.
2.3 Do No Disassemble the Batteries
1). Never disassemble the batteries.
Doing this may cause a internal short circuit in the battery, which may
lead to harmful fumes, fire, explosion, or other problems.
2). Electrolyte Gel is harmful
Electrolyte Gel should not leak from the LIR battery. Should the
electrolyte gel come into contact with the skin or eyes, flush the area
of contact immediately with fresh water and seek medical attention
immediately.
2.4 Do Not Expose the Battery to Heat or Fire
Never incinerate or dispose of the batteries in fire. This may cause an
explosion, which would be very dangerous.
PinPoint GO COLOR Battery Precautions