background image

User Instructions

ADJ Products, LLC - www.adj.com - Galaxian 3D MKII Instruction Manual Page 2

Unpacking: 

Thank you for purchasing the Galaxian 3D MKII by ADJ 

Products, LLC. Every Galaxian 3D MKII has been thoroughly tested 

and has been shipped in perfect operating condition. Carefully check 

the shipping carton for damage that may have occurred during ship-

ping. If the carton appears to be damaged, carefully inspect your fix-

ture for any damage and be sure all equipment necessary to operate 

the unit has arrived intact. In the event damage has been found or parts 

are missing, please contact our toll free customer support number for 

further instructions. Please do not return this unit to your dealer with-

out contacting customer support first. 

Introduction: 

The Galaxian 3D MKII is an incredible five channel 

DMX intelligent, green and red laser fixture. The red and green laser 

beams rotate back and forth creating amazing aerial effect on a ceiling 

or wall. The Galaxian 3D MKII can operate as a stand alone fixture, or 

in a Master/Slave configuration. The Galaxian 3D MKII can be a sound 

active fixture or it can also be controlled via DMX. This fixture is suit-

able for theaters, studios, retail stores, and other similar locations. For 

best results use fog or special effects smoke to enhance the beams 

projections.  

Customer Support:

 

ADJ Products, LLC provides a toll free cus-

tomer support line, to provide set up help and  to answer any question 

should you encounter problems during your set up or initial operation. 

You may also visit us on the web at www.adj.com for any comments 

or suggestions. For service related issue please contact ADJ Products, 

LLC. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. 

Pacific Standard Time.

 

Voice:   

(800) 322-6337

 

Fax:    

(323) 582-2941

 

E-mail:  

[email protected]

Warning!

 

To prevent or reduce the risk of electrical shock or fire, do 

not expose this unit to rain or moisture. 

Caution! 

There are no user serviceable parts inside this unit. Do not 

attempt any repairs yourself, doing so will void your manufactures war-

ranty. In the unlikely event your unit may require service please contact 

ADJ customer support.
PLEASE recycle the shipping carton whenever possible.

 Galaxian 3D MKII                                General Introduction

    3/13

GALAXIAN 3D MKII

Summary of Contents for GALAXIAN 3D MKII











Reviews: