ADJ Products, LLC - www.adj.com - Fog Fury Jett Pro Instruction Manual Page 12
Fog Fury Jett Pro
Wireless Remote Operation
Always be sure to maintain an adequate supply of American DJ
Brand Fog Juice in the fluid reservoir. Running the fog machine
dry will cause pump failure and or clogging. This is the largest
cause of failure in fog and haze machines. Only American DJ Fog
Juice is recommended and not all fog juice is created equal.
Wirelesss Remote Operation:
Start by connecting the remote
receiver to the fog machine. Set the machine to your desired wireless
remote channel setting. See page 9. Once the machine is plugged
in and turned on, a red power LED on the receiver will glow indicat-
ing the unit is receiving power. The unit has a warm up time of about
nine (9) minutes. After the unit has warmed up, a GREEN LED on
the receiver will light indicating the unit is ready to emit fog. To emit
fog, simply press the corresponding number button on the remote
for desired length of time. If the GREEN LED is on and fog does not
come out after holding the button down for 30 seconds, check the
fluid tank and make sure you have enough fog juice.
Caution:
Before removing or replacing the remote control unit
disconnect the power supply.
ON
DIP
1
2
3
4
Frequency 0
ON
DIP
1
2
3
4
Frequency 1
ON
DIP
1
2
3
4
Frequency 2
ON
DIP
1
2
3
4
Frequency 3
ON
DIP
1
2
3
4
Frequency 4
ON
DIP
1
2
3
4
Frequency 5
ON
DIP
1
2
3
4
Frequency 6
ON
DIP
1
2
3
4
Frequency 7
ON
DIP
1
2
3
4
Frequency 8
ON
DIP
1
2
3
4
Frequency 9
ON
DIP
1
2
3
4
Frequency 10
ON
DIP
1
2
3
4
Frequency 11
ON
DIP
1
2
3
4
Frequency 12
ON
DIP
1
2
3
4
Frequency 13
ON
DIP
1
2
3
4
Frequency 14
ON
DIP
1
2
3
4
Frequency 15
WiFly Channel Setting Chart
ADJ Products, LLC - www.adj.com - Fog Fury Jett Pro Instruction Manual Page 11
With this feature you are able to control the unit with DMX without the
need of XLR cables. Your DMX controller must be connected to a ADJ
WiFly TransCeiver to use this function. You are able to communicate
up to 400 feet (open line of sight)
1. Set the antenna to either a up position or down position.
2. Set the Wireless address using the dipswitches on the rear of the
the unit. The address must match the address set on the WiFly
Transceiver.
3. After you have set the WiFly address, apply power to the ADJ
WiFly Transceiver. The fixture must be set up first before you apply
power to WiFly Transceiver.
5. If everything is set up properly and the fixture is receiving a
Wireless signal, Wireless status indicator LED will glow green.
6. The Signal strength meter will display how strong of a signal the
unit is receiving.
Note: If the sync does not work, switch the power off then on again.
Fog Fury Jett Pro
WiFly DMX Set up
This feature will let you link units to run in a master-slave mode with-
out the use of XLR cables.
1. Set the WiFly address to your desire. The addresses on each fix-
ture must be the same.
2. After you have set the WiFly address, select your “Master” unit
and set your desired operating mode.
3. When using the Wireless remote control, each unit must have the
included remote receiver plugged in. The units can be set to dif-
ferent colors if desired.
Fog Fury Jett Pro
WiFly Master-Slave Set up
