manualshive.com logo in svg

aditec Bakery MIC 990, User Manual

Share
Download
aditec Bakery MIC 990 User Manual Download Page 19

User Manual MIC 990

 

 

 

 

 

 

 

                                                                                                                              

19 

Issue 18.03.2021_00

 

7.1  Separate deck  

 

 

Program-
number 

Program name 

 

Deck number 

 

Start button for 
starting the 
programs 

 

 

 

Baking time 

Steaming 
time 

Flap time 

 

 

By  pressing  one  of  the  boxes  the  controller  changes  over  to  deck 
overview (see the separate dock overview) 
 

 

7.1.1 

Status display 

 

 

 

 

 

Program out of 

operation  

 

Programm in 

operation  

 

 

 

 

 

 

inactive 

active 

 

Baking time 

 

 

 

Baking nom. time is displayed  

Baking act. time is displayed 

 

Colon flashes 

– step time is counted 

Colon don’t flashes – step time is not counted  

 

 

 

inactive 

active 

 

 

 

Steaming time 

 

 

 

 

 

Steaming nom. 
time 

Steamin act. time  Steaming act. 

time is expired  

 

 

 
Recharge of steaming time in operation (from V90.03) 

Press the button             : Steam nuzzle is switched-on for the set time 
 

 

inactive 

active 

 

 

 

Flap time 

 

 

 

 

 

Steaming nom. 
time is displayed 
flap closed   

Steaming act. 
time is displayed 
flap closed   

Steaming act. 
time is expired 
flap open   

Flap time on the end of  
the program (can be set 
by the service technician)  

Summary of Contents for Bakery MIC 990


































Reviews:

No comments

Brands by name

Popular brands

Load more brands