Addi-Data APCI-1032 Technical Description Download | Manualshive

Page: 53 / 67

background image

APCI-1032, APCI-1564 and APCI-2032

Functions of the board

53

Down counter

Fig. 8-11: Function of the down counter

To count the same number of values (4) as by up counting, the reload value is to be set
to 3.
The counter counts down to 0 and is reset to the reload value from the next changing
edge.

8.6

Watchdog (APCI-2032, APCI-1564)

The watchdog is a down-counter which resets the digital outputs after the reload value
has run down (timeout).

3 different states are available for the watchdog.

"OFF"

The watchdog is switched off. It has no influence ont the outputs.

"ON"

The watchdog is switched on by software trigger.

It controls the program course and affects the outputs through timeout.

"Alarm"

The watchdog sets alarm by resetting all outputs.

The states can be read back through software.

Time intervals can be programmed from 20 ms to 5 s in 20 ms steps.

«
...
51
52
53
54
55
...
»

Summary of Contents for APCI-1032




































































Reviews:

No comments

Related manuals for APCI-1032

Brand: Ting Pages: 5

Brand: Ingenico Pages: 10

iCLASS SE Biometric Reader

Brand: HID Pages: 50

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 6

Brand: ZKTeco Pages: 7

UHF10F Pro Reader

Brand: ZKTeco Pages: 25

Brand: Mircom Pages: 4

Brand: Axiom Pages: 4

Brand: Diablotek Pages: 1

Brand: Data Translation Pages: 164

Brand: Johnson Controls Pages: 4

Brand: Certgate Pages: 5

GTX 570 1280MB PHANTOM

Brand: Gainward Pages: 2

GTX 550 TI 1024MB GOLDEN SAMPLE

Brand: Gainward Pages: 1

ZKTeco SpeedFace Reader SF1008+

Brand: Paxton Pages: 3

Brand: Quanmax Pages: 27

Video-348PCI Series

Brand: Jaton Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands