manualshive.com logo in svg

ADC AD-78III, Installation Manual, Page: 47 / 48

Share
Download
ADC AD-78III Installation Manual Download Page 47

43

IMPORTANT

MANUAL RESET HI-LIMIT INSTRUCTIONS

DUAL TIMER MODELS ONLY

This dryer was manufactured with a burner manual reset hi-limit thermostat, and a lint/basket (tumbler) manual

reset hi-limit thermostat.  If either the manual reset hi-limit thermostat is open prior to the start of the drying

cycle, or during the cycle, the dryer will not recognize the open state of the burner hi-limit thermostat and will

start or continue through the drying cycle with no heat.  Manual reset hi-limit thermostat 

must be

 reset manually.

This hi-temperature condition may be caused due to a restricted exhaust, poor airflow, or improper burner oven

operation.  The location of the manual reset hi-limit switch is on the right side of the burner box.

WARNING:

Discontinue power to dryer before attempting to reset hi-limit.

IMPORTANT

This  dryer  is  equipped  with  a  burner

hi-limit and tumbler/lint chamber hi-limit

thermostat which must be reset manually.

WARNING:

 Discontinue power to dryer

before attempting to reset hi-limit.

ADC P/N:114093

All manuals and user guides at all-guides.com

Summary of Contents for AD-78III

















































Reviews:

No comments