ADB Safegate RELIANCE User Manual Download

Page: 69 / 76

Appendix B: POWER TABLE

Fixture type

Fixture load

Isolation transformer

CCR load

Rating

Loss

Efficiency

RS -AM (omnidirectional, inset)

35 VA

45 W

7 VA

0.85

45 VA

Fixture type

Fixture load

Isolation transformer

CCR load

Rating

Loss

Efficiency

RS -TE (omnidirectional, inset)

14 VA

25 / 35 W

4 VA

0.85

20 VA

Note

•

Extra losses in secondary cables or due to extra equipment (e.g. ILCMS remotes) are not included in above table;

these extra losses will result in a higher required size of isolation transformers.

•

Extra losses in primary cables are not included in above table; these extra losses will result in a higher required

CCR load.

•

Efficiency of the secondary transformer depends on the supplier of secondary transformers.

UM-5027, Rev. 1.0, 2020/12/10

Summary of Contents for RELIANCE



































































Search results

Summary of Contents for RELIANCE

Reviews:

Related manuals for RELIANCE

Brands by name

Popular brands

ADB Safegate RELIANCE, User Manual

Search results

Summary of Contents for RELIANCE

Reviews:

Related manuals for RELIANCE

Brands by name

Popular brands