ADB Safegate RELIANCE Omni 1-Dome User Manual Download Page 34

Page: 34 / 66

Note

If the inner pan does not separate from the cover assembly easily, use a flat bladed screwdriver to separate it by

inserting the screwdriver blade in the pry slots. There are 2 slots 180 degrees apart milled into the underside

flange of the top cover that mates with the inner cover flange.

CAUTION

Be careful. Do not pull on the LED lead cable when you lift the inner pan.
This may damage the connection!
Failure to follow this instruction can result in equipment damage.

5. Refer to

Figure 8

Disconnect the LED cable.

NOTICE

Do not pull the cable out, but carefully disconnect the LED cable by lifting the connector straight up. If not done

correctly there is a risk to damage the PCB or cable connector.

Figure 8: Disconnecting the LED cable from the optical assembly

6. Remove the inner pan from the cover. Discard the old O-ring.

Note

Always replace the cover/inner cover O-Ring seal Item whenever the inset fixture is opened. This guarantees light

fixture water tightness.

RELIANCE Omni 1-Dome,
Maintenance

24
Copyright

Summary of Contents for RELIANCE Omni 1-Dome


























































Search results

Summary of Contents for RELIANCE Omni 1-Dome

Reviews:

Brands by name

Popular brands

ADB Safegate RELIANCE Omni 1-Dome, User Manual

Search results

Summary of Contents for RELIANCE Omni 1-Dome

Reviews:

Brands by name

Popular brands