manualshive.com logo in svg

ADB Safegate RELIANCE Omni 1-Dome, User Manual

Share
Download
ADB Safegate RELIANCE Omni 1-Dome User Manual Download Page 24

Remember

Refer to FAA AC 150/5345-30 and the project site-specific plans and specifications for details on shallow base

installation.

Also follow the applicable instructions in the previous section, 

Installation on L-868 Base

 section when connecting, installing

and powering the fixture.

Figure 4: Example of a shallow base installation

1-1/2" (TYP.)

L868B FLANGE RING 12.25" O.D.

3/4" THICK, 5402/12Y

WITH O-RING GASKET (TYP.)

SEMI-FLUSH

LIGHT FIXTURE

TYPE L-85X (TYP.)

0.75"

GROUND WIRE

6 AWG OR LARGER

L868B LIGHT BASE

L-823 PRIMARY CONNECTOR

L868B SPACER RING(S)

GROMMET

2" PVC CONDUIT W/BELL END

3/4" DRAIN HOLE (CENTERED)

FIXTURE TOP

BELOW GRADE

Earth Ground

L-823 PRIMARY

GROMMET

ISOLATION TRANSFORMER
(max 3 per can)

L-823 SECONDARY CONNECTOR

Earth Ground

L868B LIGHT BASE

Earth Ground

3/4" DRAIN HOLE (CENTERED)
(if used)

L868B SPACER RING(S)

L868B FLANGE PLATE 12.25" O.D.

L868B JUNCTION HOUSING

EDGE TO BE

+0 - (-1/16)" 

EXTENSION

3/8” Anti-vibration Washer

3/8-16  Hex Cap Screw

(per FAA EB-83 (latest revision)

(per FAA EB-83 (latest revision)

4.7 RELIANCE Omni Base Assembly

The optional shallow base is shipped separately from the Omni fixture.
The shallow base is a 12-inch O.D. L-868B base can and includes connectors to attach to the external wiring. Contact the ADB

SAFEGATE Sales Department for additional information.

4.8 Installation on L-868 Base

The light assembly is shipped complete, and is ready for installation.
To install the fixture on an L-868 base, see FAA AC 150/5345-30 and the project site-specific plans and specifications for

details on L-868 base installation.

Note

Mounting bolts are not supplied with the fixture. Mounting bolts and anti-rotation lock washers are normally supplied

with the base can spacer or flange ring. If a flange ring is used, the bolt length is 1

‑

1/4 inch (32mm) plus the thickness

of the flange ring.

RELIANCE Omni 1-Dome,
Installation

14
Copyright 

©

 ADB SAFEGATE, All Rights Reserved

Summary of Contents for RELIANCE Omni 1-Dome



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands