ADB Safegate L-858 AGSF Series User Manual Download Page 33

Page: 33 / 56

Note

Check site plans and specifications for the location of the power leg (the leg where the L-823 cord set is located) in

reference to the L-867 light base. Typically, the L-867 light base is immediately under the power leg or is at the

same end, but not under the power leg. ADB Safegate’ signs are shipped with the sign product label attached to

the sign end where the power leg is located. In addition, verify that the sign legend is orientated correctly to the

taxiway or runway per the site plans when the sign is installed on the pad. If the sign legend location is not correct,

then the panels must be removed and reinstalled in the sign in the correct location.

•

For special situations where visibility would be improved, refer to FAA AC 150/5340-18 for the correct orientation.

•

For signs identifying an instrument landing system (ILS) critical area, coordinate the location and orientation with the local

FAA airway facilities personnel, and schedule installation with periodic ILS flight checks to ensure that signs do not cause

interference with the ILS electronic signal.

3.4.4 Sign Distance from Pavement Edge

Refer to

Table 5

for the distance of signs from the pavement edge. Refer to AC 150/5340-18 for more information on the

location of different types of taxiway signs.

Table 5: Recommended Sign Distance from Pavement Edge

Sign Size

Distance from Pavement ft

Distance from Pavement m

10−20

3.1−6.1

25−35

7.6−10.7

35−60

10.7−18.2

50−75

15.2−22.9

20−35

6.1−10.7

3.5 Cord set and Extension Cords

See

Figure 10

. Refer to

Table 8

for cord set and extension cord types. Refer to

Table 7

for cord set and cord parts.

Figure 10: L-823 Cord set and Extension Cords

Table 6: Cord set and Extension Cord Length

Type

Part Number

Receptacle Style

Plug Style

Standard Length

Wire

73A0107-X

Not applicable

Type II, Class A, Style

4 ft (1.22 mm)

6 ft (1.83 mm)

16/2

73A0108-X

Type II, Class A, Style

8 ft (2.44 mm)

16/2

73A0109-X

Type II, Class A, Style

8 ft (2.44 mm)

16/2

96A0286, Rev. AT, 2020/09/16

Summary of Contents for L-858 AGSF Series





















































Search results

Summary of Contents for L-858 AGSF Series

Reviews:

Related manuals for L-858 AGSF Series

Brands by name

Popular brands

ADB Safegate L-858 AGSF Series, User Manual

Search results

Summary of Contents for L-858 AGSF Series

Reviews:

Related manuals for L-858 AGSF Series

Brands by name

Popular brands