ADB Safegate AXON FAA L-852A User Manual Download Page 47

Page: 47 / 98

8. Locking:

a. Lock the secondary cables into the converter by opening the cable holes prying a thin screw driver on the cable

release opening and mounting the wires in place

b. Lock the cables by releasing screw driver from the opening.

9. Close the light.

Note

Refer to the

Closing a Light Fixture — connecting the Bottom Pan to the Top Cover

section.

5.3.9 Replacing the secondary Cable — Style-6 cord set

Figure 17: Secondary cable replacement

Tools to be used:

•

Screwdriver T25 bit

•

Flat-head screwdriver

•

Small flat head screwdriver

1. Open the light.

Note

Refer to the

Opening a Light Fixture — disconnecting the Bottom Pan from the Top Cover

section.

2. Disconnect the cable:

a. Disconnect the secondary cable from the converter by placing a small flat-head screwdriver into the opening located

at the other side of the secondary wire, and

b. Release the cable by prying the screwdriver on the cable release opening.

3. Unscrew the Strain-relief Bolt and its plate.

Make sure you dispose the old Strain-relief Bolt and its plate and use the new material.

4. Unscrew the Strain Relief Bolt, the plate and the cable gland gaskets.

Make sure you dispose the old Strain Relief Bolt, the plate and the cable gland gaskets and use the new material.

5. Remove the secondary cable

Make sure you dispose the old secondary cable and use the new secondary cable.

UM-5056, Rev. 1.0.17, 2022/12/08

Summary of Contents for AXON FAA L-852A

























































































Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Related manuals for AXON FAA L-852A

Brands by name

Popular brands

ADB Safegate AXON FAA L-852A, User Manual

Search results

Summary of Contents for AXON FAA L-852A

Reviews:

Related manuals for AXON FAA L-852A

Brands by name

Popular brands