Adaptive AlphaPremiere 9000 Series Installation Instructions Manual Download Page 24

Page: 24 / 24

Checkout procedure

After installing a sign according to the previous sections, make sure the unit is installed properly by

applying power to it. Information

similar to the following

should be displayed on the sign:

Service and maintenance

Firmware updates

The internal program or firmware (also referred to as “flash EPROM”) that runs an AlphaPremiere™ sign

may need to be updated from time to time.

To find out the availability of any updates, check this web page:

http://www.adaptivedisplays.com/support.htm.

Routine cleaning

When cleaning the case is necessary, use a soft lint-free cotton cloth (such as a pre-washed cotton diaper)

with mild soap and water. Two drops of soap per quart of water is adequate. Alcohol and cleaners with alcohol (or
any other strong solvent) are not recommended.

If the front lens becomes dusty, use a vacuum cleaner that has a soft brush on an extension wand.

9000 SERIES

9200 RED

SERIAL ADDRESS

00 HEX

SERIAL DATA

9600, 8n1

RS485 ECHO

DISABLED

INFRARED

ENABLED

SPEAKER VOLUME

[XXXX ]

PERF REV

211040001B v01.04

FPGA REV

26111401 V1.4

RAM 1

RAM 128K

10:48 AM FRI.

FEB. 23, 2001

FLASH OK

Summary of Contents for AlphaPremiere 9000 Series

























Search results

Summary of Contents for AlphaPremiere 9000 Series

Reviews:

Related manuals for AlphaPremiere 9000 Series

Brands by name

Popular brands

Adaptive AlphaPremiere 9000 Series, Installation Instructions Manual

Search results

Summary of Contents for AlphaPremiere 9000 Series

Reviews:

Related manuals for AlphaPremiere 9000 Series

Brands by name

Popular brands