Adaptec AHA-2940 - SCSI Card Installation Manual Download Page 6

5

AHA-2940/2940W Installation Guide
Part Number: 510881-00, Rev. A
Print Spec Number: 493890-00
Current Date: 7/5/95

ECN Date: 7/11/95

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AAAA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA

A

A

A

A

A

A

A

A

A

A

A

A

A

A

Installing SCSI Devices

You can connect up to a total of seven internal and 
external 8-bit SCSI devices to the AHA-2940, and up 
to 15 devices (seven 8-bit internal and eight Wide (16-
bit) internal or external SCSI devices, or 15 Wide inter-
nal and external SCSI devices) to the AHA-2940W.

Choosing SCSI Cables

The cables required to connect SCSI devices are 
determined by the type of devices you are installing, 
as described in the following table.

If you purchased your AHA-2940/2940W in an 
Adaptec kit, the kit includes an internal SCSI cable 
that allows you to connect up to two internal SCSI 
devices (the AHA-2940 kit includes a 50-pin internal 
SCSI cable, and the AHA-2940W kit includes a 
68-pin internal SCSI cable). If you are connecting 
more than two internal SCSI devices, you must 
obtain an internal SCSI cable with enough connec-
tors to accommodate all of your devices.

Adaptec sells high-quality internal and external SCSI 
cables. If your reseller does not stock these cables, 
call Adaptec directly at the number for ordering 
Adaptec software and cables listed on page 12.

When Fast SCSI devices are connected to the host 
adapter, the total length of all cables (internal and 
external) must not exceed 3 meters (9.8 ft.) to ensure 
reliable operation. If no Fast SCSI devices are con-
nected, the total length of all cables must not exceed 
6 meters (19.7 ft). See your device’s documentation 
to determine if it is a Fast SCSI device.

 SCSI Device Type

AHA-2940

AHA-2940W

8-bit Internal SCSI

50-pin internal 
SCSI cable

50-pin internal 
SCSI cable 

8-bit External SCSI

50-pin high-density 
external SCSI cable

16-bit Internal Wide SCSI 

68-pin internal 
SCSI cable 

16-bit External Wide SCSI

68-pin external 
SCSI cable

4

Summary of Contents for AHA-2940 - SCSI Card















Reviews: