background image

1

Copyright

©2004 Adaptec, Inc. All rights reserved. No part of this publication may be 
reproduced, stored in a retrieval system, or transmitted in any form or by any 
means, electronic, mechanical, photocopying, recording or otherwise, without the 
prior written consent of Adaptec, Inc., 691 South Milpitas Blvd., Milpitas, CA 95035.

Trademarks

Adaptec and the Adaptec logo are trademarks of Adaptec, Inc., which may be 
registered in some jurisdictions.

Microsoft, Windows 98SE, Windows 2000, Windows Me, and Windows XP are 
trademarks of Microsoft Corporation in the US and other countries, used under 
license.

All other trademarks are the property of their respective owners.

Changes

The material in this document is for information only and is subject to change 
without notice. While reasonable efforts have been made in the preparation of this 
document to assure its accuracy, Adaptec, Inc. assumes no liability resulting from 
errors or omissions in this document, or from the use of the information contained 
herein.

Adaptec reserves the right to make changes in the product design without 
reservation and without notification to its users.

Disclaimer

IF THIS PRODUCT DIRECTS YOU TO COPY MATERIALS, YOU MUST HAVE 
PERMISSION FROM THE COPYRIGHT OWNER OF THE MATERIALS TO AVOID 
VIOLATING THE LAW WHICH COULD RESULT IN DAMAGES OR OTHER 
REMEDIES.

Summary of Contents for ACS-100














Reviews: