ADA International Group Ltd., No.6 Building, Hanjiang West Road #128,
Changzhou New District, Jiangsu, China
Made In China
SPECIFICATIONS
Working range*
.......................................................
Accuracy **
..............................................................
Angle of beam reception
.........................................
Protection
.................................................................
Batteries
....................................................................
Working temperature
............................................
Storage temperature
..............................................
Dimensions
................................................................
Weight
.........................................................................
* Working range may be reduced due to unfavorable environmental conditions (e.g. direct
sunlight). The receiver can react to nearby pulsating light (LED lamps, monitors).
** Depends on the distance between the receiver and line laser.
INSTALLATION/BATTERY REPLACEMENT
Unscrew the screw from the battery compartment cover. Open the battery
compartment cover. Insert 2 batteries, type AAA/1,5V. Observe the polarity. Close
the cover. Fasten the screw.
Note! Remove the batteries from the receiver, if you are not going to work with
it for a long time. Long-term storage may cause corrosion and self-discharge
of batteries.
MOUNT FOR THE RECEIVER
Receiver can be securely fixed with the help of a mount (16). If necessary, the receiver
can be attached to steel parts using magnets (14).
ADJUSTMENT OF THE RECEIVER
The receiver must be adjusted to the frequency of the line laser before use. All
settings are saved after switching off.
Choose one of the pre-installed frequencies for the setting. Switch on the receiver to
enter this mode. Press and hold sound button (11) for more thn 20 sec. All arrows
(18 and 20), middle mark (19) will light up on the display. Blinking sector shows the
selected frequency variant. Press frequency adjustment button (10) to change the
frequency variant. To save your choice, press and hold button (11) for more than 5
sec. If the receiver doesn’t react on the laser beam, choose another frequency variant
(distance to check isno less than 5 m). Sector, indicating the selected frequency
variant, will blink 3 times when switching on the receiver.
USAGE
Use the receiver mode in bright light, when the laser beam is poorly visible. Minimum
distance to use a receiver is 5 m. Switch on the detector mode on the line laser. Switch
on the receiver by pressing On/Off button. Switch on or switch off the backlight by
short pressing On/Off button. Press and hold On/Off button for more than 3 sec to
switch Off the receiver. Select the measurement frequency by pressing button (10).
Icon of the selected mode for scanning beam will appear on the display:
±
1 mm (one
bar),
±
2 mm (2 bars). Choose the sound (2 variants) or mute mode by pressing sound
button (11). When the sound mode is selected, the loud speaker icon is shown on the
display. Place the receiver sensor towards the laser beam and move it up and down
(horizontal beam scanning) or right and left (vertical beam scanning), untill arrows
will appear on the display (LED arrows will light up). There will be a sound alarm when
the arrows will appear on the display (if the sound is ON). Move the receiver towards
the arrows. When the laser beam is in the middle of the receiver, a continious beep
sounds and the display shows the middle mark (LED center indicator lights up). Marks
on the sides of the receiver correspond to the middle position of the laser beam on
the receiver. Use them to mark the surface to be marked. When marking, the receiver
must be strictly in vertical position (horizontal beam) or strictly in horizontal position
(vertical beam). Otherwise the mark will be shifted. Laser target (15) is on the back
side of the receiver. It is used as a template without switching on the receiver.
CARE AND CLEANING
•
Handle the receiver with care.
•
Never immerse it into the water or other liquids.
•
Clean with dry soft cloth only after any use. Do not use any cleaning agents or
solvents.
•
•
WARRANTY
This product is warranted by the manufacturer to the original purchaser to be free
from defects in material and workmanship under normal use for a period of two
(2) years from the date of purchase. During the warranty period, and upon proof of
purchase, the product will be repaired or replaced (with the same or similar model
at manufactures option), without charge for either parts of labour. In case of a defect
please contact the dealer where you originally purchased this product. The warranty
will not apply to this product if it has been misused, abused or altered. Without limit-
ing the foregoing, leakage of the battery, bending or dropping the unit are presumed
to be defects resulting from misuse or abuse.
OPERATING MANUAL
LASERMARKER 70
Laser receiver
EXCEPTIONS FROM RESPONSIBILITY
The user of this product is expected to follow the instructions given in operators’
manual. Although all instruments left our warehouse in perfect condition and ad-
justment the user is expected to carry out periodic checks of the product’s accuracy
and general performance. The manufacturer, or its representatives, assumes no re-
sponsibility of results of a faulty or intentional usage or misuse including any direct,
indirect, consequential damage, and loss of profits. The manufacturer, or its repre
-
sentatives, assumes no responsibility for consequential damage, and loss of profits
by any disaster (earthquake, storm, flood ...), fire, accident, or an act of a third party
and/or a usage in other than usual conditions.
The manufacturer, or its representatives, assumes no responsibility for any damage,
and loss of profits due to a change of data, loss of data and interruption of business
etc., caused by using the product or an unusable product. The manufacturer, or its
representatives, assumes no responsibility for any damage, and loss of profits caused
by usage other thsn explained in the users’ manual.
The manufacturer, or its representatives, assumes no responsibility for damage
caused by wrong movement or action due to connecting with other products.
WARRANTY DOESN’T EXTEND TO FOLLOWING CASES:
1. If the standard or serial product number will be changed, erased, removed or wil
be unreadable.
2. Periodic maintenance, repair or changing parts as a result of their normal runout.
3. All adaptations and modifications with the purpose of improvement and expan
-
sion of normal sphere of product application, mentioned in the service instruction,
without tentative written agreement of the expert provider.
4. Service by anyone other than an authorized service center.
5. Damage to products or parts caused by misuse, including, without limitation,
misapplication or nrgligence of the terms of service instruction.
6. Power supply units, chargers, accessories, wearing parts.
7. Products, damaged from mishandling, faulty adjustment, maintenance with
low-quality and non-standard materials, presence of any liquids and foreign objects
inside the product.
8. Acts of God and/or actions of third persons.
9. In case of unwarranted repair till the end of warranty period because of damages
during the operation of the product, it’s transportation and storing, warranty doesn’t
resume.
WARRANTY CARD
Name and model of the product __________________________________________
Serial number___________________________Date of sale______________________
Name of commercial organization ________________________________________
stamp of commercial organization
Warranty period for the instrument explotation is 24 months after the date of original
retail purchase. During this warranty period the owner of the product has the right for
free repair of his instrument in case of manufacturing defects. Warranty is valid only
with original warranty card, fully and clear filled (stamp or mark of thr seller is obliga
-
tory). Technical examination of instruments for fault identification which is under the
warranty, is made only in the authorized service center.
In no event shall manufacturer be liable before the client for direct or consequential
damages, loss of profit or any other damage which occur in the result of the instru
-
ment outage.
The product is received in the state of operability, without any visible damages, in full
completeness. It is tested in my presence. I have no complaints to the product quality.
I am familiar with the conditions of qarranty service and i agree.
purchaser signature _______________________________
Before operating you should read service instruction!
If you have any questions about the warranty service and technical support contact seller
of this product
5–70 m
– «fine adjustment» ±1 mm
– «rough adjustment» ±3 мм
90°
IP 54
2 × 1,5 V (AAА)
–10 °C...+50 °C
–20 °C...+70 °C
160 х 80 х 25 mm
0,15 kg
