Aeris Suspend
Installation Instructions
Lithonia Lighting Outdoor
One Lithonia Way, Conyers, GA 30012
Phone: 800-279-8041 Fax: 770-918-1209
www.lithonia.com
Part Number: RJ5210199 Rev A
Revision Date: 3/4/08
WBA (Wall Bracket) INSTALLATION
CAUTION: APPLY A CONTINUOUS BEAD
OF WEATHER - PROOF CAULKING BETWEEN MOUNTING PLATE AND WALL TO
ENSURE WEATHER - TIGHT INTEGRITY OF ELECTRICAL COMPONENTS.
Tools Required: 3/16" allen wrench, 9/16" socket or wrench.
1. Secure base plate to wall with (4) 1/4" fastener (supplied by others) using the (4) holes
located on the outer corners of the base plate. Check the base plate to confirm that
it is level and plumb in all directions. (See figure 1).
2. Prepare the cover plate by attaching the Aeris mounting block to the cover plate using
(2) 3/8" diameter by 1-1/4" bolts with (2) 3/8" diameter lockwashers by inserting the bolts
and washers into the mounting block through the cover plate and thread into the
threaded steel bar stock. Use a 9/16" socket or wrench and tighten securely (See figure
2). When installing the fixture in the lens down position, place the curved portion of the
cover plate upwards . When installing the fixture in the lens up position (damp location
only), place the straight portion of the cover plate upwards.
3. Check the gasketing(factory installed) on the backside of the cover plate to ensure
that it is in place.
4. Place and tighten (4) 3/8" diameter by 1-1/4" stainless steel hex socket head screws
(requires 3/16" allen wrench) into the threaded opening of the cover plate by turning
approximately 6-7 full turns.
5. To prepare fixture for installation, refer to steps 2 and 3 per pole mounted instructions
on page 1.
6. Pull the wires from the fixture through the mounting block on the cover plate. Place
fixture onto the mounting block, being sure the wires are not being pinched.
7. Tighten the locking hex head bolt inside the arm with a 9/16" socket to 20-30 ft. lbs.
torque.
8. Make wiring connections, being careful to observe proper polarity and grounding.
9. Slide the assembly over the base plate, tighten the top (2) 3/8" x 1-1/4" stainless steel
hex socket head screws until 3/8" to 1/4" of the screw is still visible.
10. Tighten the bottom (2) 3/8" x 1-1/4" stainless steel hex socket head screws until 3/8"
to 1/4" of the screw is still visible.
11. Alternating between the top two and bottom two sets of screws, gently tighten until
snug, (approximately one thread showing on each screw).
12. Continue fixture installation and lamp installation (refer to step 6 per the pole mounted
instructions above).
13. Secure strut receiver to small strut wall mount plate using the 10-24 x 3/4" thread rolling
screw in the top hole on the center of the plate. The locating pin on the receiver should
sit in the second hole on the center of the plate (See Figure 3).
14. Attach aluminum rod using the two 1/4" x 1-1/4" black oxide screws to the receiver
on the top of the fixture and to the receiver on the wall mount plate using 5/32" allen
wrench. Tighten until head of screw is flush with the receiver block.
15. Secure the small strut wall mount plate to wall with two 1/4" fasteners (supplied by
others). Check the plate to confirm that it is level and plumb in all directions (See Figure
4).
Page 2
1/4" black
oxide screws
Strut
Receiver
3/4" thread
rolling screw
Figure 3
Figure 4
Figure 2
Aeris Mounting Block
(4) Socket Held Screws
Figure 2
Aeris Mounting Block
(4) Socket Held Screws
Figure 2
Aeris Mounting Block
(4) Socket Held Screws
Figure 1
Seal
By others
To wall
Gasket
(factory installed)
Base Plate
Cover Plate
(4) 1/4” fasteners
(by others)
Silicone
Sealant by
Others
Figure 1
Seal
By others
To wall
Gasket
(factory installed)
Base Plate
Cover Plate
(4) 1/4” fasteners
(by others)
Silicone
Sealant by
Others
Seal
By others
To wall
Gasket
(factory installed)
Base Plate
Cover Plate
(4) 1/4” fasteners
(by others)
Seal
By others
To wall
Gasket
(factory installed)
Base Plate
Cover Plate
(4) 1/4” fasteners
(by others)
Silicone
Sealant by
Others
(4) Socket
Head Screws
Threaded
Steel Bar
Stock
Figure 2
