INSTRUCTION
SHEET
MSD (PDT) 7
Embedded 360°
Motion Sensor
© 2016 Acuity Brands Lighting Inc., All Rights Reserved.
1/2016
COVERAGE PATTERNS
SPECIFICATIONS
PHYSICAL SPECS
SIZE: 1.34” H x 1.18” W x 2.62” D
WEIGHT: 3 oz
MOUNTING: Required Hole Size 1.125”
Material Thickness 0.25” max
COLOR: White
ELECTRICAL SPECS
OPERATING VOLTAGE : 12-24 VDC
CURRENT DRAW: 4 mA
DIMMING LOAD: Sinks < 20mA;
~40 Ballasts / LED drivers (0-10VDC)
ENVIRONMENTAL SPECS
OPERATING TEMP: 32° to 140° F (0° to 60° C)
RELATIVE HUMIDITY: 20 to 90% non-condensing
ROHS COMPLIANT
Lens rotates 15° to
enable adjustment
HIGH VIEW
0 ft
15
0 m
4.6
30 24 18 12 6 0 ft 6 12 18 24 30
9.2 7.4 5.4 3.6 1.8 0 m 1.8 3.6 5.4 7.4 9.2
30
24
18
12
6
0 ft
6
12
18
24
30
9.2
7.4
5.4
3.6
1.8
0 m
1.8
3.6
5.4
7.4
9.2
LOW VIEW
0 ft
9
0 m
2.7
18 15 12 9 6 3 0 ft 3 6 9 12 15 18
5.4 4.6 3.6 2.7 1.8 0.9 0 m 0.9 1.8 2.7 3.6 4.6 5.4
18
15
12
9
6
3
0 ft
3
6
9
12
15
18
5.5
4.6
3.7
2.7
1.8
0.9
0 m
0.9
1.8
2.7
3.7
4.6
5.5
HIGH VIEW
0 ft
15
0 m
4.6
30 24 18 12 6 0 ft 6 12 18 24 30
9.2 7.4 5.4 3.6 1.8 0 m 1.8 3.6 5.4 7.4 9.2
30
24
18
12
6
0 ft
6
12
18
24
30
9.2
7.4
5.4
3.6
1.8
0 m
1.8
3.6
5.4
7.4
9.2
LOW VIEW
0 ft
9
0 m
2.7
18 15 12 9 6 3 0 ft 3 6 9 12 15 18
5.4 4.6 3.6 2.7 1.8 0.9 0 m 0.9 1.8 2.7 3.6 4.6 5.4
18
15
12
9
6
3
0 ft
3
6
9
12
15
18
5.5
4.6
3.7
2.7
1.8
0.9
0 m
0.9
1.8
2.7
3.7
4.6
5.5
9 FT MOUNTING
15 FT MOUNTING
• Recommended for walking motion detection from mounting heights between 8 ft (2.44 m) and 20 ft (6.10 m)
• Initial detection of walking motion along sensor axes at distances of 2x the mounting height up to 15 ft (4.57 m)
and 1.75x up to 20 ft (6.10 m).
• Provides 12 ft (3.66 m) radial detection of small motion when mounted at 9 ft (2.74 m)
• At the 7.5 ft (2.29 m) hanging height of a typical pendant or suspended mount fixture the sensor provides 10 ft
(3.05 m) radial detection of small motion.
• Initial detection will occur earlier when walking across sensor’s field of view than when walking directly at sensor
WIRING (DO NOT WIRE HOT)
RED
- 12-24 VDC Power Input
VIOLET
- Low Voltage Dim Output (0-10 VDC)
BLACK
- Low Voltage Common
Note: Do not connect the dimming wires of
multiple sensors in parallel.
0 - 10 VDC
LED DRIVER / BALLAST
DC Power (12-24V)
DIAGRAM 1. INSTALLATION EXAMPLE
DIAGRAM 2. ASSEMBLY DETAIL
OPTIONAL SPACER
PAD LOCATION
PRY UP UNDER LIP ON SIDES WITH
ARROWS TO UNSNAP LENS ASSEMBLY
OPTIONAL SPACER
PAD LOCATION
INSTALLATION
• If not pre-installed, locate sensor body so that detector faces down through 1.125” hole in luminaire.
• Align lens assembly legs with holes in sensor body and snap together (max material thickness 0.25”).
• Apply foam spacer pads onto sensor body if needed to ensure snug fit with fixture.
• Assembly rotates 15° to enable coverage pattern adjustment after installation.
• To unsnap lens assembly, pry up under lip at spots on lens assembly denoted by arrows.
5-year limited warranty. Full warranty terms located at:
www.acuitybrands.com/CustomerResources/Terms_and_conditions.aspx
Note: Specifications subject to change without notice.
Actual performance may differ as a result of end-user environment and application.