background image

B. Part List

4

Deck 

26.8 inches long, Canadian Maple 

Wheels
Weight
Max Speed
Range
Max Incline Rate

11%

Max Rider Weight
Power
Battery Capacity
Charging Time
Remote Controller

ACTON BLINK® GO electrical skateboard
Remote controller
Skateboard Charger

Run time up to 45 min;

Recharge time 2 hours for regular charger

Make sure the power switch is turned o  whenever the ACTON BLINK® 

Lite V2

 is not in 

use or it will drain the battery. When the battery is drained, it is very susceptible to 

damage. When the ACTON BLINK® 

Lite V2

 is not in regular use, recharge the battery at 

least once a month until normal use is resumed.

Use only the recommended charger and use caution when charging. The charger should 

be regularly examined for possible damage to the cord, plug, enclosure or other parts. The 

charger should be operated only by an adult. Do not operate the charger near flammable 
materials. Unplug the charger and disconnect from ACTON BLINK

®

 

Lite V2

 when not in 

use and charging is complete.

E.

 

Radio Interference Precautions

ACTON  BLINK® 

Lite V2

 incorporates  a  sophisticated  communication  system  to 

ensure connection between the remote controller and the skateboard. The connection 

could be unstable or lost when the remote controller’s battery is low. Stop riding once the 

LED on the 

appears dimmer.  Human  body  could    

interfere  with remote signal as well. Don’t put 

remote in the pocket while riding.
Try to avoid areas with high-power electromagnetic radiating equipment, such as radio 

towers,  powerlines  or  radar.  In  some  rare  cases,  connection  may  also  be  lost  due  to 

unpredictable causes. As a safety precaution, ACTON BLINK® 

Lite V2

 will shut o

 immediately 

when the connection is lost. If a loss of connection happens more than once, stop 

use immediately and avoid using ACTON BLINK® 

Lite V2

 again in such areas.

Please contact ACTON for further assistance.

II.

 

PRODUCT INFORMATION

A.

 

Technical Specification

70 mm, 78A hardness
7.8 lbs/3.5 kg
10 mph/16 kmph
5 miles/9 km

180 lbs/85 kg
MAX 250W
55.4 Wh
2 hour
2.4 Ghz Bluetooth

remote appears dimmer. Human body could interfere with remote signal as well. Don’t 

put remote in the pocket while riding.

Summary of Contents for LITE V2









Reviews: