background image

www.acti.com

 
 

Hardware Manual 

                 

Precautions 

Read these instructions 

Read all the safety and operating instructions before using this product.   

 

Heed all warnings 

Adhere to all the warnings on the product and in the instruction manual. Failure to follow the 

safety  instructions  given  may  directly  endanger  people,  cause  damage  to  the  system  or  to 

other equipment. 

 

Servicing   

Do not attempt to service this product yourself as opening or removing covers may expose you 

to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 

 

Trademarks 

ACTi  and  ACTi  logo  are  registered  trademarks  of  ACTi  Corporation.  All  other  names  and 

products used in this manual are registered trademarks of their respective companies.   

 

Liability 

Every reasonable care has been  taken during the  writing  of this manual.  Please  inform your 

local office if you find any inaccuracies or omissions. ACTi will not be held responsible for any 

typographical or technical  errors and reserves the right to make changes to the  product and 

manuals without prior notice.   

 

 

 

Summary of Contents for Z71
























Reviews: