ACTi TCD-2500 User Manual Download Page 14 | Manualshive

Page: 14 / 20

background image

www.acti.com

TCD-2500 Hardware User’s Manual

14

Basic Connections

Follow the procedures below to connect the IP device to the respective apparatuses.

1) Connect an analog monitor to IP device video out (BNC connector)

2) Connect the power adaptor to IP device

3) Connect IP device

’s Ethernet port to Network switch (via RJ45 connectors).

4) Connect a PC to the Ethernet switch (via RJ45 connectors)

«
...
12
13
14
15
16
...
»

Summary of Contents for TCD-2500





















Reviews:

No comments

Related manuals for TCD-2500

Express5800/320Ma

Brand: NEC Pages: 86

Brand: Lanner Pages: 43

Eserver xSeries 360 Type 8686

Brand: IBM Pages: 74

8480 - Eserver xSeries 205

Brand: IBM Pages: 174

Brand: Hologic Pages: 30

Brand: Rohde & Schwarz Pages: 126

Brand: LiveU Pages: 14

Brand: TYAN Pages: 70

EonServ 7000 Series

Brand: Infotrend Pages: 2

Brand: BRONKHORST Pages: 19

Xtreme PC NG-6600

Brand: Chip PC Pages: 4

Brand: Compatible Systems Pages: 75

PD02 PCoIP Zero Client

Brand: EVGA Pages: 2

PD02 PCoIP Zero Client TAA Compliant

Brand: EVGA Pages: 2

Brand: UNIVIEW Pages: 44

Brand: GIGA-BYTE TECHNOLOGY Pages: 90

Brand: Oracle Pages: 83

Brand: Dell EMC Pages: 127

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands