background image

www.acti.com

  Hardware Manual 

                 

30 

Connecting the DI/DO and Audio Devices (Optional) 

Depending on your surveillance needs, you may connect digital input or output or audio input / 

output devices to your camera. The camera comes with one (1) terminal block for both digital and 

audio input / output devices. 

 

How to Connect DI/DO Devices 

Digital Input (DI) devices can be used to notify the camera about an activity in the camera site. DI 

can be triggers of events. For example, you can connect a “panic button” to the camera; as such 

when the panic button is pressed, the alarm signal will be sent through the camera. Other 

common DI device applications are emergency button, smoke detector, passive infrared sensor, 

etc. 

 

Digital Output (DO) devices are external devices that are activated by the camera upon an event 

inside the camera. For example, you can connect an “alarm horn” to the camera; as such when 

an event occurs inside the camera (e.g. detected intruder), the alarm horn will sound. Other 

common DO device applications are motion-triggered lights, electric fence, magnetic door locks, 

etc. 

 

Press and hold the orange tab as you insert the wire through the pin slot, then release the orange 

tab to secure the wire. 

 

 

To connect digital input / output devices (DI/DO), map the pins to one of the pin combinations 

below: 

 

Device 

Pin 

 

Mapping Instructions 

Digital Output 

(DO) 

DIO PW 

Connect the wires of the output device to 

DIO

 

PW

 

and 

DO

DO 

Digital Input   

(DI) 

DIO GND 

Connect the wires of the input device to 

DIO

 

GND

   

and 

DI

DI 

For Audio Use 

Summary of Contents for B910

















































Reviews: