ACTi B511 Hardware Manual Download Page 2

Page: 2 / 27

www.acti.com

Hardware Manual

Table of Contents

Precautions

Safety Instructions ........................................................................... 5

Introduction

The List of Models ............................................................................ 6

Package Contents ............................................................................. 7

Physical Description ........................................................................ 8

Before Installation

Prepare the Power Adapter (Optional) ............................................ 9

Prepare the DI/DO Connector (Optional) ...................................... 11

Installation Procedures

Mounting Solutions ........................................................................ 14

Mounting on the Ceiling or Wall .................................................... 16

Step 1: Drill the Holes .................................................................. 16

Step 2: Prepare the Camera ........................................................ 17

Step 3: Install the Camera............................................................ 18

Step 4: Connect the Cable(s) ....................................................... 18

Step 5: Access the Camera Live View ......................................... 20

Accessing the Camera

Configure the IP Addresses ........................................................... 21

Access the Camera ......................................................................... 25

Summary of Contents for B511




























Search results

Summary of Contents for B511

Reviews:

Related manuals for B511

Brands by name

Popular brands

ACTi B511, Hardware Manual

Search results

Summary of Contents for B511

Reviews:

Related manuals for B511

Brands by name

Popular brands