ACS-CONTROL-SYSTEM GmbH
l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]
35
33
11. Safety advices
11. Safety advices
Please read the following safety advices and the assembly in
chapter 2
before installation and keep it for
future reference.
Proper use
The
M3-31-device
is designed for the evaluation and display of sensor signals.
Danger! Careless use or improper operation can result in
personal injury and/or cause damage to the equipment.
Control of the device
The panel meters are checked before dispatch and sent out in perfect condition. Should there be any visible
damage, we recommend close examination of the packaging. Please inform the supplier immediately of any
damage.
Installation
The
M3-31-device
must be installed by a suitably
qualified specialist
(e.g. with a qualification in industrial
electronics).
Notes on installation
• There must be no magnetic or electric fields in the vicinity of the device, e.g. due to transformers, mobile
phones or electrostatic discharge.
• The
fuse rating
of the supply voltage should not exceed a value of
6A N.B. fuse
.
• Do not install
inductive consumers
(relays, solenoid valves etc.) near the device and
suppress
any
interference with the aid of RC spark extinguishing combinations or free-wheeling diodes.
• Keep input, output and supply lines separate from one another and do not lay them parallel with each
other. Position “go” and “return lines” next to one another. Where possible use twisted pair. So, you
receive best measuring results.
• Screen off and twist sensor lines. Do not lay current-carrying lines in the vicinity. Connect the
screening
on one side
on a suitable potential equaliser (normally signal ground).
• The device is not suitable for installation in areas where there is a risk of explosion.
• Any electrical connection deviating from the connection diagram can endanger human life and/or can
destroy the equipment.
• The terminal area of the devices is part of the service. Here electrostatic discharge needs to be avoided.
Attention! High voltages can cause dangerous body currents.
• Galvanic isolated potentials within one complex need to be placed on an appropriate point (normally earth
or machines ground). So, a lower disturbance sensibility against impacted energy can be reached and
dangerous potentials, that can occur on long lines or due to faulty wiring, can be avoided.
33
11. Safety advices
11. Safety advices
Please read the following safety advices and the assembly in
chapter 2
before installation and keep it for
future reference.
Proper use
The
M3-31-device
is designed for the evaluation and display of sensor signals.
Danger! Careless use or improper operation can result in
personal injury and/or cause damage to the equipment.
Control of the device
The panel meters are checked before dispatch and sent out in perfect condition. Should there be any visible
damage, we recommend close examination of the packaging. Please inform the supplier immediately of any
damage.
Installation
The
M3-31-device
must be installed by a suitably
qualified specialist
(e.g. with a qualification in industrial
electronics).
Notes on installation
• There must be no magnetic or electric fields in the vicinity of the device, e.g. due to transformers, mobile
phones or electrostatic discharge.
• The
fuse rating
of the supply voltage should not exceed a value of
6A N.B. fuse
.
• Do not install
inductive consumers
(relays, solenoid valves etc.) near the device and
suppress
any
interference with the aid of RC spark extinguishing combinations or free-wheeling diodes.
• Keep input, output and supply lines separate from one another and do not lay them parallel with each
other. Position “go” and “return lines” next to one another. Where possible use twisted pair. So, you
receive best measuring results.
• Screen off and twist sensor lines. Do not lay current-carrying lines in the vicinity. Connect the
screening
on one side
on a suitable potential equaliser (normally signal ground).
• The device is not suitable for installation in areas where there is a risk of explosion.
• Any electrical connection deviating from the connection diagram can endanger human life and/or can
destroy the equipment.
• The terminal area of the devices is part of the service. Here electrostatic discharge needs to be avoided.
Attention! High voltages can cause dangerous body currents.
• Galvanic isolated potentials within one complex need to be placed on an appropriate point (normally earth
or machines ground). So, a lower disturbance sensibility against impacted energy can be reached and
dangerous potentials, that can occur on long lines or due to faulty wiring, can be avoided.
33
11. Safety advices
11. Safety advices
Please read the following safety advices and the assembly in
chapter 2
before installation and keep it for
future reference.
Proper use
The
M3-31-device
is designed for the evaluation and display of sensor signals.
Danger! Careless use or improper operation can result in
personal injury and/or cause damage to the equipment.
Control of the device
The panel meters are checked before dispatch and sent out in perfect condition. Should there be any visible
damage, we recommend close examination of the packaging. Please inform the supplier immediately of any
damage.
Installation
The
M3-31-device
must be installed by a suitably
qualified specialist
(e.g. with a qualification in industrial
electronics).
Notes on installation
• There must be no magnetic or electric fields in the vicinity of the device, e.g. due to transformers, mobile
phones or electrostatic discharge.
• The
fuse rating
of the supply voltage should not exceed a value of
6A N.B. fuse
.
• Do not install
inductive consumers
(relays, solenoid valves etc.) near the device and
suppress
any
interference with the aid of RC spark extinguishing combinations or free-wheeling diodes.
• Keep input, output and supply lines separate from one another and do not lay them parallel with each
other. Position “go” and “return lines” next to one another. Where possible use twisted pair. So, you
receive best measuring results.
• Screen off and twist sensor lines. Do not lay current-carrying lines in the vicinity. Connect the
screening
on one side
on a suitable potential equaliser (normally signal ground).
• The device is not suitable for installation in areas where there is a risk of explosion.
• Any electrical connection deviating from the connection diagram can endanger human life and/or can
destroy the equipment.
• The terminal area of the devices is part of the service. Here electrostatic discharge needs to be avoided.
Attention! High voltages can cause dangerous body currents.
• Galvanic isolated potentials within one complex need to be placed on an appropriate point (normally earth
or machines ground). So, a lower disturbance sensibility against impacted energy can be reached and
dangerous potentials, that can occur on long lines or due to faulty wiring, can be avoided.
The
DAP-311-
-device is designed for the evaluation and display of sensor signals.
The
DAP-311-device
must be installed by a suitably qualified specialist (e.g. with a qualification in
industrial electronics).
