AcrEase MR44BE Owner'S Manual Download Page 26

 

24 

AcrEase Pull Behind Mower 

Warranty Policy 

 

1.   

Kunz Engineering, Inc., warrants to the owner that each new product is free of defects 
in workmanship and material for the length of 12 months from the date of purchase.  
Kunz Engineering, Inc., agrees to provide replacement parts for any defective parts at 
no charge to the owner.   The customer is responsible for transportation of the mower 
to and from the dealer. 

 
2. 

All AcrEase mowers at the time of sale have been designed and equipped to conform 
to the U.S.  EPA Evaporative Standards.  Kunz Engineering, Inc. warrants to the owner 
that all emission reducing evaporative components are free from defects in 
workmanship and material for the length of 2 years.  Kunz Engineering, Inc., agrees to 
provide replacement parts for any defective emission reducing evaporative 
components at no charge to the owner.   The customer is responsible for 
transportation of the mower to and from the dealer. 

 
3.       All warranty parts must be replaced with original factory parts. 
 
4. 

Parts will be shipped by regular ground delivery.  If next day or second day service is 
required, the customer will be responsible for additional shipping costs.  

 
5.       This warranty will not cover parts damaged for the following reasons: 

a.  Failure to follow proper set-up procedures outlined in the Owner's Manual 
b.  Operator misuse or neglect 
c.   Accidents 
d.   Design alterations 
e.   Repairs not done according to manufacturer's instructions 
f.   Commercial, rental, or municipality use of a homeowner model 

 
6.       Normal wear items such as belts, blades, tires, and bearings will not be covered  
        under this warranty unless the original part is shown to be defective. 
 
7. 

Mowing too fast in very heavy, long grass can cause the engine to pull down and 
disengage the blade clutch.   Damage to the clutch springs, clutch bearing, and  

drive belt resulting when the clutch is allowed to slip will not be covered with this 

warranty.  (Finish cut models with centrifugal clutches only.)   

 
8. 

The engines are warranted separately for parts and labor by the engine manufacturer.  
All engine warranty repairs must be done by a dealer who is authorized to work on that 
brand of engine.  Please refer to the engine manual for warranty coverage details. 

 

Summary of Contents for MR44BE



























Reviews: