ACR Electronics RCL-75 Product Support Manual Download Page 20

Y1-03-0158H 

 

19

 

 
 

 
 
 
 
 

 

EC DECLARATION OF CONFORMITY 

ACR Electronics, Inc. hereby declares that the following product is in conformity with 
Directive  2004/108/EC  of  the  European  Parliament  and  of  the  Council  of  15 
December  2004  on  Electromagnetic  Compatibility  (EMC  Directive).  In  accordance 
with  the  Directive,  the  product  will  be  marked  with  the  CE  conformity  marking  as 
follows: 

 

Product:  

 

Searchlight 

 

 

 

Model: RCL-75 

Regulations and 

EN 60945: 2002: Emissions:

 

Standards:

 

CISPR 16-1:1999 (Conducted Emissions) 

 

CISPR 16-1:1999 (Radiated Emissions) 

EN 60945: 2002: Immunity: 

IEC 61000-4-2: 1995 (Electrostatic Discharge) 
IEC 61000-4-3: 1995 (Radiated Immunity) 

 

IEC  61000-4-6:  1996  (Conducted  Immunity,  Power 

and I/O Leads) 

IEC 61000-4-11: 1994 (Voltage Dips and Interrupts) 

Manufacturer:  

ACR Electronics Inc.  

European 

ACR Electronics Inc.

 

 

5757 Ravenswood Road 

Representative:  

(European Office) 

 

Fort Lauderdale, FL 33312 

1 Rose Cottages, Pitmore Lane, 

 

USA 

Sway, Lymington, Hampshire 

 

SO41 6BX  UK 

Signed on behalf of ACR Electronics Inc. 

 

Signed: 

__________________________________________ 

 

Name:  Kerry Greer 

 

Date: 

February 26, 2009 

Title: 

Executive Director - 
Research & Development 

 

Document RCL-75-002 

 

 

 

 

This Declaration complies with 

ISO/IEC 17050-1:2004 

 
 
 

ACR Electronics, Inc. is registered by UL to ISO 9001:2000

 

Summary of Contents for RCL-75





















Reviews: