manualshive.com logo in svg

ACPro AULD36W2/A-D, Owner'S Manual

Share
Download
ACPro AULD36W2/A-D Owner'S Manual Download Page 4

Contents 

1 Safety Precautions ............................................................ 1
2 Product Introduction ......................................................... 5

2.1 Operating Range ....................................................................5

 

2.2 Standard Accessories .............................................................5

 

2.3 Optional Accessories..............................................................5

 

3 Installation .......................................................................... 5

3.1 Installation Preparation ..........................................................5

 

3.2 Unit Installation .................................................................... 11

 

3.3 Electrical Installation ............................................................ 17

 

3.4 Check after Installation ......................................................... 22

 

3.5 Test Running ........................................................................ 23

 

4 Maintenance ..................................................................... 2

7

4.1 Failures Not Caused by Faults of The AC ............................ 2

7

 

4.2 Error Code ........................................................................... 2

9

 

4.3 Unit Maintenance ................................................................. 

30

 

4.4 Notice on Maintenance ........................................................ 

31

 

4.5 After-Sales Services ............................................................. 

36

 

3.

6

 

Functions

 ......................................................

.....

.................. 2

4

 

Summary of Contents for AULD36W2/A-D










































Reviews:

No comments

Brands by name

Popular brands

Load more brands